Memory Reset; Troubleshooting Guide - PRASTEL TC1000 Manuel D'installation

10. Memory reset

In order to cancel all the transmitters from the memory it will be enough to follow this procedure:
1. Take off the power supply from the control unit.
2. Press and keep pressed the "Radio Learn" button.
3. Power the control unit.
4. The control unit emits a long beep followed by two short beeps.
5. At this stage release the "Radio Learn" button , after few seconds the control unit emits two short beeps . At this stage the memory has been
cancelled.
Avoid putting the connection cables of buttons, security devices and inputs close to those of the power supply of the control unit and of the motor.
Some parts of the control unit are subject to dangerous voltage. The control unit must be installed and programmed only by qualified professionals.
Always use a device that ensures the disconnection of all poles of the control unit's power supply.
This device can be:
a switch (connected directly to the power supply terminals) with a contact's minimum distance of 3 mm for each pole, or it can be a device connected
to the power network.
For connecting the card and the motors we recommend to use cables with double isolation as imposed by the laws in force; the minimum cross sec-
tion of the single conductor must not be less than 1mm² and not more than 2.5mm².
The presence of a dampness or metal parts in the walls nearby may negatively influence the capacity the system; it is therefore important to carefully
put the antenna and the transmitters away from walls and/or metal structures, away from the ground and not on the ground.
A tuned antenna is needed to maximize the performances in terms of the range; the range would only be a few meters without it.
If the cable supplied is too short, then do not join an extension to it , but replace the whole cable with one of the right length whose impedance is 50
Ohm (RG 58 type). The cable should never be longer than 10 meters. This control unit has a photocells test circuit.

12. Troubleshooting guide

PROBLEM
1) The green led "power on" does not
lights on.
2) The buttons of the transmitter do not
have any effect on the control unit.
3) Pressing the UP button of the transmit-
t e r t h e a u t o m a t i o n
4) Pressing the DOWN button of the
transmitter the automation closes.
5) The led "photo" is
6) The led stop" is turned off.
7) It is not possible to enter into the learn-
ing phase.
6-1622609 rev.2 03/08/2015
WARNINGS AND ADVICES
•
The control unit is not powered.
•
The fuse is damaged.
•
The transmitter has not been learnt.
•
The transmitter is not compliant with the control
unit.
•
The battery of the transmitter is flat.
•
The motor wiring has been performed in a
c l o s e s .
wrong way.
•
The motor wiring has been performed in a
wrong way.
•
not lit.
The photocell is under alarm because of an
obstacle.
•
The input photo has not been jumpered.
•
The button used for the stop is a normally open
contact.
•
The input is not jumpered in case the stop
button is not used.
•
The automation is not still.
ITA
CAUSES
ENG FRA ESP DEU POR
SOLUTIONS
•
Check the wiring and power the control unit.
•
Check the functioning of the fuse with a tester and
replace with another one with the same features
(6.3A 250V).
•
Execute the learning of the transmitter (see
chap.6).
•
Check that the transmitter is a B.ro 433Mhz.
•
Replace the battery of the transmitter.
•
Wire again the motor inversing the clamps 13 and
14
•
Wire again the motor inversing the clamps 13 and
14
•
Take off the obstacle..
•
Jumper the inputs 2 and 5 if the photocell is not
used.
•
Check the button type and in case replace it.
•
Jumper the inputs 1 and 2 in case that the stop
button is not used.
•
Give a stop impulse and try again.
7 / 8