Obtaining Steam; Basic Cleaning - Black & Decker BXCO1200E Mode D'emploi

bag paper does not come out of the filter holder.
Š Once done it, do same as above with ground coffee
Š When finished, with Selection Control (D) at position 0
Š Extract the single dose filter and throw away the used
POD
Š Wash the filter holder and the filter for the pod (drying
it well)

Obtaining steam:

Š The steam is used to foam milk for cappuccino, and also
to heat other liquids.
Š Turn the appliance on using the on/off switch (F)
Š Wait until the pilot light (E) changes to blue colour which
will indicate that the appliance has reached an adequate
temperature.
Š Place a recipient under the steam tube.
Š Select Steam Position with Control Knob (D)
Š Steam only will begin to exit.
Š When you have enough, turn back the control knob (D)
to 0 position and remove the recipient.
Auto-off feature:
Š The Black + Decker machines are designed to save
energy
To that end, after some minutes, if during this period
the user has not performed any action on it, the unit
switches to energy saving mode
To return to normal operation you should just switch on
the button (F)
Once you have finished using the applian-
ce:
Š Turn the appliance off, pushing the on/off switch (F)
Š Unplug the appliance to the mains.
Š Remove the water from the water tank.
Š Clean the appliance
CLEANING

Basic cleaning

Š Disconnect the appliance from the mains and let it cool
before undertaking any cleaning task.
Š Clean the equipment with a damp cloth with a few drops
of washingup liquid and then dry.
Š Do not use solvents, or products with an acid or base pH
such as bleach, or abrasive products, for cleaning the
appliance.
Š Do not let water or any other liquid get into the air vents
to avoid damage to the inner parts of the appliance.
(Original instructions)
Š Neither parts of this appliance are suitable for cleaning in
the dishwasher.
Š After washing, dry all the parts before fitting them
together and storing.
Cleaning the Frothing Wand (Fig 1)
Š CAUTION! The frothing wand, frothing tip, and frothing
sleeve may be VERY HOT
Š It is recommended to purge and wipe the frothing wand
after steaming milk to prevent deposits of dirt and before
turning off the machine
Š To do this, pull the black frothing sleeve down and clean
under warm running water.
Š Fill a cup with a bit of water, immerse the frothing wand
into the water, turn the Control Knob to the "Steam icon"
for a few seconds, and then turn the Control Knob(D)
towards the center to the position "0".
Š Use a cloth to dry the frothing wand and replace the
frothing sleeve
Š If extremely clogged, the frothing tip can be unscrewed,
and soaked in warm soapy water.
Š In case no steam comes out of the frothing wand, harde-
ned milk blocks its path.
Š Carefully use a needle to loosen the milk residue from
the opening of the frothing tip (Fig 1) to remove any
blockage,
Š Once clean, rinse with running water from the tap and
reassemble it. Then steam again
How to deal with lime scale incrustations:
Š For the appliance to work correctly it should be kept free
of lime scale or magnesium incrustations caused by the
use of hard water.
Š To prevent this kind of problem, we recommend the use
of water with low lime or magnesium mineralisation.
Š However, if it is not possible to use the kind of water
recommended above, you should periodically remove
the lime scale from the appliance:
Every 6 weeks if the water is "very hard".
Š
Every 12 weeks if the water is "hard".
Š
Š To do so, we recommend the use of the specific product
Decal for this kind of machine, which can be found in
specialised shops and authorised technical services.
Š Homemade solutions are not recommended in the des-
caling of this appliance, such as the use of vinegar.
ENGLISH
7