Accessories - Stanley FatMax FME630 Mode D'emploi

Use
Warning! Let the tool work at its own pace. Do not overload.
Adjust the depth of cut.
u
If necessary, it and adjust the parallel fence.
u
Switching on and off
Switching on
Keep the lock-off button (2) depressed and press the on/
u
off switch (1).
Release the lock-off button.
u
Switching off
Release the on/off switch.
u
Planing
Hold the tool with the nose piece of the shoe resting on
u
top of the workpiece surface.
Switch the tool on.
u
Move the tool steadily forward to perform the cutting
u
stroke.
Switch the tool off after the stroke has been completed.
u
Rebating (ig. F)
Fit and adjust the parallel fence.
u
Proceed as for planing.
u
Chamfering edges (ig. G)
The V-groove in the nose piece of the shoe enables you to
chamfer edges at 45°, 30° and 15° angles.
Hold the tool at an angle with the desired groove (20)
u
around the edge of the workpiece and perform the cutting
stroke.
Parking rest (ig. H)
Your planer is equipped with a parking rest (21) that automati-
cally lowers into place when the tool is lifted from the work
surface. When planing, the parking foot raises as the tool is
pushed forward. When the parking foot is lowered, the planer
can set on the work surface without the blade touching.
Hints for optimum use
Move the tool along the grain of the wood.
u
If the grain is cross or curly, or if the workpiece material is
u
a hard type of wood, adjust the depth of cut to take only a
very thin shaving at each pass and take several passes to
achieve the desired result.
To keep the tool in a straight line, press down the front of
u
the tool at the start, and press down the back of the tool at
the end of the cutting stroke.
(Original instructions)

Accessories

The performance of your tool depends on the accessory used.
Stanley Fat Max accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
The following types of cutting blades can be obtained from
your local retailer:
-
Tungsten carbide tipped reversible cutting blades (part
no. X35007, supplied per pair)
-
High-speed steel reversible cutting blades (part no.
X24192-XJ11, supplied per pair)
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance, switch off and
unplug the tool.
Regularly clean the ventilation slots in your tool using a
u
soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Replacing the drive belt (ig. I)
Loosen the screws (15) and remove the cover (16).
u
Remove the old drive belt.
u
Place the new belt (17) over the pulleys. Place the belt
u
over the large pulley (18) irst, then over the small pulley
(19), whilst manually rotating the belt steadily.
Put the cover back in place and tighten the screws.
u
Motor brush inspection and replacement (ig. J)
Brushes should be regularly inspected for wear.
Remove brush cap (22). The brushes should slide freely
u
in brush box. If brushes are worn down to .3" (8mm) they
should be replaced.
To reinstall, push new brush back into brush box. If replacing
existing brush, maintain same orientation as when removed.
Replace the brush cap (do not overtighten).
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be itted:
Safely dispose of the old plug.
u
Connect the brown lead to the live terminal in the new
u
plug.
Connect the blue lead to the neutral terminal.
u
Warning! No connection is to be made to the earth terminal.
Follow the itting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
ENGLISH
7