Electrical Safety - Stanley FatMax FME630 Mode D'emploi

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 17
ENGLISH
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.

Electrical safety

#
This tool is double insulated; therefore no earth wire
is required. Always check that the power supply
corresponds to the voltage on the rating plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Stanley Fat Max Service
Centre in order to avoid a hazard.
Features
This tool includes some or all of the following features.
1. On/off switch
2. Lock-off button
3. Shavings discharge outlet
4. Shavings discharge outlet selector
5. Planing depth adjustment knob
6. Planing depth graduation
Assembly
Warning! Before assembly, make sure that the tool is switched off
and unplugged.
Replacing the cutting blades (ig. A)
The cutting blades provided with this tool are reversible.
Replacement cutting blades can be obtained from your local
retailer.
Removing
Loosen the bolts (7) using the spanner supplied.
u
Slide the blade (8) out of the holder.
u
Reverse the blade so that the unused side comes in posi-
u
tion. If both sides are worn, the blade must be replaced.
6
(Original instructions)
Fitting
Slide the blade into the holder until it is against the end
u
stop.
Tighten the bolts using the spanner supplied.
u
Warning! Always replace both cutters.
Adjusting the depth of cut (ig. B)
The depth of cut is indicated by the marking (9). The setting
range can be read from the graduation (6).
Turn the planing depth adjustment knob (5) to the required
u
depth of cut.
Turn the knob to the 'P' postion whenever the tool is not in
u
use.
Fitting and removing the parallel fence (ig. C)
The parallel fence is used to for optimum control on narrow
workpieces.
Thread the knob (11) into the hole on the side of the
u
planer and securely tighten.
Loosen the parallel fence adjustment knob (10).
u
Slide the parallel fence into the desired position.
u
Securely tighten the parallel fence adjustment knob.
u
Note : The parallel fence should be below the planer when
installed correctly.
To remove the parallel fence proceed in reverse order.
u
Connecting a vacuum cleaner to the tool (ig. D)
An adaptor is required to connect a vacuum cleaner or dust
extractor to the tool. The adaptor can be purchased from your
local Stanley Fat Max retailer.
Slide the adaptor (12) over the shavings discharge outlet
u
(3).
Connect the vacuum cleaner hose (13) to the adaptor.
u
Fitting the shavings collection bag (ig. E)
The shavings collection bag is particularly useful when working
in conined spaces.
Slide the connecting plate (14) of the bag over either side
u
of the shavings discharge outlet (3).
To prevent chips from coming out opposite side of shav-
u
ings discharge outlet, move the shavings discharge outlet
selector (4) to the opposite side from the bag.
Emptying the shavings collection bag
The shavings collection bag should be emptied regularly while
using it to prevent blocking.
Unzip the bag and empty it before continuing.
u

Publicité

Table des Matières
loading

Table des Matières