Electrical Connection; Illustrated Description; Operating Instructions; Placement And Testing - grupostayer P910 Instructions D'emploi

Integrated Dust Extraction (Figure C)
A chip/dust bag 16 can be used for smaller jobs. Insert
the sleeve of the chip/dust bag firmly into the chip ejector
3. Empty the chip/dust bag 16 at regulary intervals to
maintain optimum dust collection.

3.3 Electrical connection

Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified on
the nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.

3.4 Illustrated description

1 Planing depth scale
2 Depth adjustment knob
3 Sawdust ejector
4 Lock-off button for On/Off switch
5 On/Off switch
6 Screw for belt cover
7 Belt cover
8 Planer base plate
9 V-grooves
10 Blade drum
11 Clamping element for blade
12 Fastening screw for planer blade
13 Carbide blade
14 Allen key (not included)
15 Handle
16 Chip/dust bag
17 Alternatively output chip
18 Parallel guide
19 Scale for rebating width
20 Locking nut for adjustment of rebating width
21 Fastening bolt for parallel and beveling guide
22 Mains electric
23 Technical data (labels)
24 Fastening bolt for rebating depth stop
25 Rebating depth stop
26 Drive belt
27 Large pulley
28 Small pulley

4. Operating instructions

4.1 Placement and testing

Switching On and Off
To start the machine, first push the lock-off button for the
On/Off switch 4 and then press the On/Off switch 5 and
keep it pressed.
To switch off the machine, release the On/Off switch 5.
For safety reasons, the On/Off switch 5 cannot be
locked; it must remain pressed during the entire
operation.

4.2 Adjustment operation

Adjusting the Planing Depth
ENGLISH
10
With the adjustment knob 2, the planing depth can be
adjusted variably from 0–3 mm using the planing
depth scale 1
Planing (Figure D)
Set the required planing depth and place the front part of the
planer base plate 8 against the workpiece.
Apply the machine to the workpiece only when
switched on. Otherwise there is danger of
kickback when the cutting tool jams in the
workpiece.
Switch the machine on and guide the machine with even
feed over the surface to be planed. To achieve high-grade
surfaces, work only with low feed and apply pressure on the
centre of the planer base plate.
When machining hard materials (e.g. hardwood) as well as
when utilising the maximum planer width, set only low
planing depths and reduce planer feed, as required.
Excessive feed reduces the surface quality and can lead to
rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity and give
the machine longer life.
– Switch on the machine.
– Apply the supporting pressure onto the front part of the
planer base plate and slowly push the machine forward).
This tilts the park rest upward so that the rear part of the
planer base plate faces on the workpiece again.
– Guide the machine over the surface to be planed with
even feed.
Beveling Edges (Figure E)
The V-grooves (9) in the front planer base plate allow quick
and easy beveling of workpiece edges. Depending on
required bevel width, use the corresponding V-groove. For
this, place the planer with the V-groove onto the edge of the
workpiece and guide it along the edge.
Planing with Parallel (Figure F-G)
Mount the parallel guide 18 to the machine using the
corresponding fastening bolt 21. Depending on the
application, mount the rebating depth stop 25 with fastening
bolt 24 to the machine.
Loosen the locking nut 20 and adjust the requested rebating
width on the scale 19. Tighten the locking nut 20 again.
10
Slot used measure a (mm)
None 0 - 4
Small 2 - 6
Medium 4 - 9
Large 6 - 10