Lt1000 Controls Keypad Controls; About Hq Software - RIDGID SeeSnak LT1000 Mode D'emploi

Battery Status LEDs Chart
BATTERY EXTERNAL POWER
STATUS NOT CONNECTED
FULL Solid green
MED Solid green and red
LOW Solid red, 4 beeps
DEAD Solid red for 5 sec,
5 sec long beep
and shutdown
Outlet Power
For plug in operation, a double-insulated AC/DC power
supply is supplied to reduce wall outlet voltage to the cor-
rect voltage for the LT1000.
The external power supply is intended for in-
NOTICE
door use only.
To power the system up with the power cord, locate the
power supply. The power supply cord has two sections,
one of which plugs into a standard 110-120V two-bladed
outlet (US) at one end and plugs into a power supply at
the other end. The second section runs from the power
supply to the back of the LT1000 and plugs into the jack
marked at the far left side front panel of the unit
(Figure 24) .
With dry hands, connect the two sections together and in-
sert the jack plug into the jack on the LT1000. Route
the cord along a clear path and with dry hands plug the
power supply into a matching outlet. If using an extension
cord ensure it is of adequate wire gauge. For cords of 25
feet, a minimum gauge of 18AWG is required. For cords
greater than 25 feet, a minimum gauge of 16 AWG is re-
quired.
NOTICE
If external power is unreliable and produces
transient voltage spikes, the LT1000 video may freeze. In
this case simply power cycle the LT1000 off and then on.
Job data will not be lost, but current distance count may be
reset.
If the laptop is plugged into AC and the
WARNING
laptop AC adapter is not isolated, then a hot ground
could damage a laptop via the USB grounding connection.
Use only a battery or an isolated power supply to power
the LT1000 and any laptop used with it
EXTERNAL POWER
CONNECTED
LEDs OFF
LEDs OFF
LEDs OFF
LEDs OFF
SeeSnake
LT1000 Controls
Keypad Controls
Arrow Keys: Used to move among menu choices and adjust
variables (such as contrast) up and down. Used to rotate
screen image.
Select Key: Used to choose options in the Units menu (Auto,
Meters and Feet).
Menu Key: Used to bring up a menu of display options such
as Color, Brightness, Contrast, Units.
Brightness Key: Used to directly control the camera LED's
brightness up or down.
Microphone Mute Key: Used to mute the microphone while
recording or activate it to record comments during an inspec-
tion.
Sonde Key: Used to activate the built-in Sonde for tracing
the location of the camera head.
*Image Flip Key: Used to flip the image on the display ver-
tically
Zero Key: Used to establish a temporary zero-point for the
distance counter for units equipped with the Count Plus .
Power Key: Used to power the LT1000 display ON or OFF.
*Photo Key: Captures a still photo of the camera image as
shown.
*Video Key: Starts or stops the capture of a video clip.
*Autolog Key: Starts Autologging capture of a series of still
photos stored with the current job.
*Photo Tag Key: Creates a new still photo and allows you
to apply custom comments or stored tags to it.
*Job Management Key: Accesses a menu of job and report
management options.
*Playback Key: Plays back current recording, if any.
*Some of the keypad controls will have no effect unless the HQ
Software is running.

About HQ Software

HQ software enables you to create, manage and store im-
ages, audio and video from the LT1000. You can use HQ
to quickly and automatically create reports which can be
emailed to a customer, or created in HTML form and
handed to the customer on a thumb drive, or burned to
DVD. HQ software also makes it easy to organize and
store job records for future reference if needed.
HQ software is described in detail in the HQ built-in help
files found at http://www.hq.ridgid.com/ .
® LT1000
13