Silverline 1000A AC Mode D'emploi page 4

GB
Introduction
Thank you for purchasing this Silverline tool. This manual contains information
necessary for safe and effective operation of this product. This product has unique
features and, even if you are familiar with similar products, it is necessary to read this
manual carefully to ensure you fully understand the instructions. Ensure all users of the
tool read and fully understand this manual.
Description of Symbols
The rating plate on your tool may show symbols. These represent important information about
the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
DO NOT use in rain or damp environments!
Caution!
Risk of electrocution!
Class II construction (double insulated for additional protection)
Conforms to relevant legislation and safety standards.
Environmental Protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or retailer
for recycling advice.
Technical Abbreviations Key
Volts
V
~, AC Alternating current
Ampere, milli-Amp
A, mA
Diameter
Ø
Hz Hertz
Direct current
⎓, DC
Watt, kilowatt
W, kW
Ohms (resistance)
Ω
Farad (capacitance)
F
4
Original Instructions
Specification
Display: ...............................................3-1/2 digits LCD (1999 max reading)
Ranges: ...........................AC Current (200A, 1000A) 50-60Hz (clamp only),
AC Voltage (750V) 40-400Hz (probes only),
Resistance (200Ω, 20kΩ) (probes only)
Insulation test 20MΩ, 2000MΩ (external unit)
Over-range indication: ..............................Figure '1' only shown on display
Negative polarity indication: .......................... Figure '-' shown before value
Sampling rate: .................................................3 times per second (approx.)
Meter category class: ...............................................................CAT. II, 1000V
Test leads: ........................................................................CAT. II, 1000V, 10A
Max. jaw opening/conductor size: .................................................. Ø50mm
Operating temperature: .................... 0°C – 40°C (<75% relative humidity)
Storage temperature: .....................-10°C – 50°C (<85% relative humidity)
Battery: ...................................................................................9V 6F22 (PP3)
Dimensions (L x W x H):..................................................240 x 102 x 47mm
Weight: .................................................................. 300g (including battery)
The following specifications assume a 1-year calibration cycle and an operating
temperature of 18°C to 28°C (64°F to 82°F) at relative humidity up to 80% unless
otherwise noted.
Range Resolution
AC Current
Display: sine wave rms, average response
Frequency range: 50-60Hz Overload protection: 1200A within 60 seconds
200A 100mA
1000A 1A
AC Voltage
Input impedance : 9M Ω
Max. allowable input voltage :
Display: sine wave rms, average response
750V DC/AC rms
750V 1V
DC Voltage
Input impedance : 9M Ω
1000V 1V
Resistance
Overload protection : 250V DC/AC rms
200Ω +Continuity 100mΩ
200KΩ 100 Ω
DC Voltage (1000V) (probes only),
Accuracy
± (% of reading) + number of least
significant digits)
±(2.5% + 5)
<700A : ± (2.5% + 5), 700-800A
: ± (5% + 5), >800A (>800A
reading is only for reference)
Frequency response: 40Hz – 400Hz
±(2.0% + 5)
Overload protection : 1000V DC/AC rms
±(1.2% + 5)
±(1.2% + 5)
±(1% + 3)