Moulinex masterchef gourmet QA404G Mode D'emploi page 17

• Make sure that the appliance is switched off before locking the blender (d).
• Lock the blender jug (d) on the outlet (a4) by rotating it clockwise.
• Place the food in the blender jug, and lock the lid (d2) itted with the measuring cap (d3), by rotating it anti-
clockwise.
2.2 - USAGE
• Start by turning the selector button (a1) to the desired position according to the recipe.
Use the "Pulse" position for better mixing control and for a better blending of your preparation.
You can add food through the hole in the measuring cap (d3) during preparation.
• To stop the appliance, turn the button (a1) to "0".
Tips :
You can prepare:
- inely blended soups, cream soups, stewed fruit, milkshakes and cocktails.
- liquid batter (pancake, fritters, Yorkshire pudding, wafles, clafoutis and custard lans).
If ingredients stick to the sides of the bowl when mixing, stop the appliance. Remove the blender, and push the food
down onto the blades and put your blender back to continue your preparation.
• Never ill the blender jug with boiling liquid. Only use liquids or foods at simmering temperatures or below.
• Never run the blender jug empty.
• Always use the blender jug with its lid.
• Never remove the lid before the blades have stopped completely.
• Always pour liquid ingredients into the blender jug irst before adding solid ingredients.
2.3 - DISMANTLING THE ACCESSORY
• Wait for the appliance to come to a complete stop before removing the blender by unlocking it in the anti-clockwise
direction and put back the cover (a5) by locking it on the outlet (a4) (clockwise).
3 - MINCING
(DEPENDING ON MODEL)
ACCESSORIES USED :
- Attachment holder (e)
- Assembled mincer head (f)
3.1 - FITTING THE MINCER ATTACHMENT
• Press the button (a2) to release the multi-function head (a3) and raise it until it locks in place.
• Place the attachment (e) and lock it in the anti-clockwise direction such that the outlet is in alignment with the appliance.
• Place the multi-function head (a3) in the horizontal position by pressing the button (a2) once again.
3.2 - ASSEMBLING THE MINCER HEAD
• Hold the body (f1) by the feed tube, with the wider opening uppermost.
• Insert the feed screw (f2) (long shaft irst) into the body (f1).
• Fit the blade (f3) onto the short shaft protruding from the feed screw (f2) with the cutting edges facing outwards.
• Fit the chosen screen (f4 or f5) on the blade (f3), aligning the two lugs with the two notches in the body (f1).
• Screw the nut (f6) home on the body (f1) in the clockwise direction, without locking it.
• Check the assembly. The shaft should have no play, neither should it be able to turn on its own.Otherwise, repeat
the assembly procedure.
3.3 - FITTING THE MINCER HEAD ON THE APPLIANCE
• Facing the attachment outlet (e), insert the assembled mincer head (f) inclined to the right, aligning the two
bayonets in the mincer head with the two notches in the attachment. Push the mincer head home into the
attachment and turn the mincer head anti-clockwise until it latches with the feed tube in the vertical position.
• Place the removable tray (f8) on the feed tube.
3.4 - USAGE, TIPS AND DISMANTLING
• Make sure that the safety cover (a5) is locked correctly (clockwise) on the high-speed outlet (a4).
• Place a container to collect the preparation in front of the appliance.
• Run the appliance by turning the selector (a1) to speed "3" or "4".
• Push the meat, piece by piece, down the feed tube, using the pusher (f7). Never push the ingredients down the
feed tube with your fingers or any other utensil.
• To stop the appliance, turn the selector to "0" speed and wait for the appliance to come to a complete stop.
MO_KITCHEN-8080012364-01.indd 17
17
EN
22/2/13 1:34 PM