Technical Data - VOLTCRAFT VC-PB-PD45 W Mode D'emploi

Briefly press the function switch (1) to display the internal rechargeable battery level. The
remaining capacity of the rechargeable battery is indicated by the lit LEDs as follows:
1 LED: Remaining capacity up to 25%
2 LEDs: Remaining capacity up to 50%
3 LEDs: Remaining capacity up to 75%
4 LEDs: Remaining capacity up to 100%
• Charge the internal rechargeable battery as soon as only 1 LED lights up.
• Open the rubber cover (8) and connect the Micro USB plug of the included USB charging
cable to the Micro USB input (7).
• Connect the USB-A plug to a suitable USB power source (please refer to the technical data).
The charging time is approx. 19 hours for a 5 V/2 A (10 W) charger.
• You can also use the included USB-C
battery via the USB-C input (6). Charging time is approx. 12.5 hours for a 5 V/3 A (15 W)
TM
charger and approx. 4 hours for a 15 V/3 A (45 W) Power Delivery (PD) charger.
• The product cannot be charged using simultaneously the Micro USB input and USB-C
input. If two chargers are connected, the internal rechargeable battery is charged via the
USB-C input.
TM
• The battery level indicator (2) flashes during charging.
0 – 25% 25 – 50%
LED 1 Flashes blue Solid blue
LED 2 Off Flashes blue
LED 3 Off
LED 4
Off
• As soon as the internal rechargeable battery is fully charged, the battery level indicator will
turn off.
• Disconnect the cable from the product and the power source as soon as the internal
rechargeable battery is fully charged.
• Close the rubber cover (8) to protect the product from dust and jet water. The product is
ready for use.
If you only use the product occasionally, we recommend that you fully charge the
internal rechargeable battery every 6 months in order to retain maximum capacity.
If the product only has a residual battery capacity of 2% during use, it switches off
automatically. In this case, the internal rechargeable battery must be charged.
Charging mobile devices
• A fast charge is possible via the orange marked USB-A output 1 (5). In addition, this output
can be used to charge the devices with different voltages (5 V, 9 V and 12 V).
• The USB-C output (6) can be used to charge devices with different voltages (5 V, 9 V,
TM
12 V, 15 V, 20 V) and with USB Power Delivery (PD 45 W).
You can charge up to four devices at the same time. The charging currents of the
USB outputs can be found in "Technical data". Check the charging current of your
mobile device.
• Connect your mobile device to one of the USB outputs.
• The battery level indicator glows steadily and indicates the current charge level of the power
bank.
The internal rechargeable battery must be sufficiently charged so that 2 or 3 devices
can be charged at a time.
• If the charging process does not start automatically, press the function switch to turn on the
product.
• Monitor the charging process. Disconnect the USB cable from the product and the mobile
device as soon as the charging process is completed.
If the internal rechargeable battery level becomes too low, the product will turn off
automatically to prevent excessive discharge of the internal rechargeable battery.
LED light
• Press the function switch twice quickly to switch on the LED light (9) with 100% luminosity.
Press the function switch once to switch to low luminosity (20%).
• Then press the function switch again to change the light mode and switch to flashing light and
SOS signal. The light turns on each time the function switch is pressed in the following order
after turning on the LED light:
Continuous light 100% → steady light 20% → flashing light → SOS signal → light off
• Press the function switch twice quickly to switch on the light again. Switch off the light directly
by pressing the function switch twice quickly.
charging cable to charge the internal rechargeable
TM
50 – 75% 75 – 99%
Solid blue Solid blue
Solid blue Solid blue
Off Flashes blue Solid blue
Off Off Flashes blue
Carabiner hook
• Connect the carabiner hook to the eyelet (10) to attach the product, for example, to a
backpack.
• You can also hang the product on a suitable hook without the carabiner hook. Make sure that
the product does not fall.
Troubleshooting
Problem
Battery level indicator
LEDs are not bright
enough.
TM
LEDs light up even
though the charging
cable is disconnected.
100%
Care and Cleaning
Solid blue
• Disconnect the product from all the connected devices before cleaning.
Solid blue
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may
Solid blue
damage the housing or cause the product to malfunction.
Solid blue • This product does not contain any components that require maintenance. Never attempt to
open or disassemble it.
• Use a lint-free cloth to clean the product. Do not press too hard on the housing, as this can
lead to scratch marks.
• Dust can be easily removed using a soft and clean long-haired brush.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus fulfil your statutory obligations and contribute to environmental protection.

Technical Data

Input voltage/current ..................... Micro USB: 5 V/DC 2 A, 9 V/DC 2 A, 12 V/DC 1.5 A
Input/output voltage/current .......... USB-C
Output voltage/current .................. USB-A (orange) Output 1: 5 V/DC 3 A, 9 V/DC 2 A,
Battery .......................................... LiPo, 30000 mAh 111 Wh
LED light ....................................... 8x LEDs 1 W, colour temperature 6000 – 6500 K
Luminous flux ............................... 100 - 120 lumens (100%), approx. 24 lumens (20%)
Protection class ............................ IP66
Operating/storage temperature .... 0 to +45 °C
Dimensions (L x W x H) ................ 166 x 92 x 33 mm
Weight .......................................... 620 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopying, microfilming or capturing in
electronic data processing systems) requires prior written approval from the publisher. Reprinting, also in part, is
prohibited. This publication reflects the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
Cause Solution
Incompatible charging cable Use the included charging
used. cable.
Unsuitable charger used. Use the charger with correct
technical data. Check if the
charger is defective.
Disconnect the USB plug and
Poor contact at Micro USB
connect it again.
input or USB output.
LEDs glow for a while after LEDs will go off automatically
the charging cable has been after approx. 15 seconds.
disconnected.
: 5 V/DC 3 A, 9 V/DC 3 A, 12 V/DC 3 A,
TM
15 V/DC 3 A, 20 V/DC 2 A, PD 45 W
12 V/DC 1.5 A
USB-A output 2 + 3: 5 V/DC 2.4 A max.
*2159613_v1_1019_02_hk_m_en