Base Selection (Multi-Cordless Function); Base Adjustment; De-Registering Of Cordless Phones (Multi-Cordless Function) - BRONDI DC6010TR Mode D'emploi

3. Insert the registration code (that of the DC6010TR is 0000) and press
shows " Sel. Base ".
4. Select the base (1 to 4) to which you want to register the cordless, using the buttons CH+
and CH-.
5. Press , the display shows "
6. On the base, press and hold pressed the button
"registratioin performed".
7.5.3 RETURN TO FACTORY ADJUSTMENT (CORDLESS PHONE)
1. Press MENU and then use the buttons CH+ and CH- to scroll the list, up to select "
".
System
2. Press the button
list up to select "
3. Reset PT
3. Press to confi rm, for some seconds, the display shows "
confi rmation sound, and the handset returns to stand-by. All memories of the lists and the
Number Book shall be deleted, the ring volume shall be reset to level 2, melody to "Type
1" and the cordless name shall be deleted.

7.6 BASE SELECTION (MULTI-CORDLESS FUNCTION)

If your cordless has been registered to 2 or more bases (up to 4), you can choose on which
base the handset shall work.
1. Press MENU and then use the buttons CH+ and CH- to scroll the list, up to select "
".
Settings
2. Press the button
a. "
Sel. Base Auto
b. "
Sel. Base Base n
"n" base.
3. Press to confi rm.
To adjust the functions "7. BS Settings" you must insert the PIN code of the base (the default
adjustment is 0000).
7.7.1 CHANGE OF BASE PIN CODE
You can modify the PIN code of the base as follows:
1. Press MENU and then use the buttons CH+ and CH- to scroll the list, up to select "
Settings ".
2. Press the button
3. Insert the PIN code (default code: 0000) and press twice
".
PIN
4. Dial the new code (4 fi gures) and press
5. Dial again the code and press
beep, otherwise an error sound.
6. Press the button

7.7.2 DE-REGISTERING OF CORDLESS PHONES (MULTI-CORDLESS FUNCTION)

If several cordless phones are connected to the same base, you can cancel the registration
of one as follows:
1. Press MENU and then use the buttons CH+ and CH- to scroll the list, up to select "
".
Settings
2. Press the button
list up to select "
2. Reset PT
followed by the numbers of all cordless phones registered on that base.
3. Press the number corresponding to the cordless you want to de-register (1 to 4).
4. Press . The cordless shall be de-registered. The display of the cordless shows the text
" Non Reg. ".
7.7.3 SELECTION MODE
You can choose between two different selection modes: decade selection or multi-
frequency. The wrong programmation of the section will not allow to call any number.
If you do not know the type of switchboard to which you are connected, make a test
programming the selection on multi-frequency, if you do not cannot dial the number, then
program the selection on "decade".
1. Press MENU and then use the buttons CH+ and CH- to scroll the list up to select "
gs".
Settin
DC6010TR-lingue
".
Searching
, insert the PIN code (4 fi gures, default: 0000), press
", press the button
, and choose between:
" (the cordless will be connected to the nearest base);
" with n=1...4: the cordless will be connected only to the selected

7.7 BASE ADJUSTMENT

, the display shows "
Enter PIN BS
, the display shows "
, siif the code is correct, you will hear a confi rmation
to return to stand-by.
, insert the PIN code of the base (4 fi gures), press
", press the button
17
17
, the display
, until the cordless sounds, signalling
and scroll the
. The display shows "
Reset PT ?
" then you hear a
Reset..
".
, the display shows "
Con f . PIN
".
and scroll the
. The display shows "
Reset PT ?
28-10-2005, 14:14
5.
".
6. BS
7. BS
New
7. BS
",
7. BS