Oscartielle SATURNO Série Mode D'emploi page 19

ENGLISH
1 - Description of the unit
The SATURNO line of display cabinets are built-in units with a usable internal length of 937 mm (MODEL 100), 1250 mm
(MODEL 133), 1875 mm (MODEL 200) and 2500 mm (MODEL 250) in the versions for deli/dairy products, packaged
fruit/vegetables and packed meats. All these cabinets can be multiplexed, they are equipped with a system of forced air
ventilated refrigeration and they can have either an incorporated compressor unit or an external one. The general
aesthetic characteristics and overall dimensions are clearly illustrated in FIG. 1.
2 - Handling the unit
This furniture item has plastic feet (fig. 4A) or wooden pallets (fig. 4B) for cage packaging (on request), which allows for
movement with a fork lift truck. Only authorised expert personnel should handle the unit. FIG. 2 shows the weight of the
units and fork lengths of the relative lifting points.
3 - Receipt and storage
On delivery, make sure the unit has not been damaged during transport. Check the condition of the packaging: if the
packaging is damaged, check the contents in the presence of the carrier. For storage, make sure that the unit is protected
against the weather and stored at a temperature between -25°C and +55°C; 30 - 95% relative humidity. Take special care
when unpacking the unit, as the packaging contains various parts and/or accessories needed to complete the display unit
(spacers, raised edges, etc). Remove the plastic feet from the unit (fig. 4A) or wooden pallets (fig. 4B) and remove the
transparent perimeter protection. Place the display unit exactly where you plan to install it. Move the unit properly: never
drag by its sides!
Warning: Inform the Manufacturer immediately if the unit arrives damaged. Any delay in doing so relieves the
Manufacturer of all liability. The Manufacturer is not liable for any damage to the unit during handling and storage.
4 - Installation and environmental conditions
The unit should be placed on a perfectly flat floor. When fully loaded, the display cabinet should not vibrate (see FIG. 5).
The efficiency of the unit may be endangered if it is not perfectly level!
The display cabinet should never be placed in areas where explosive gas substances are used.
The unit should not be left outdoors or exposed to the rain (see FIG. 3).
The performance of the cabinet refers (according to the international standard EN ISO 23953-1/2) to environmental
climatic class 3 which consists of a room temperature of 25°C with relative humidity of 60%.
Sufficient space must be provided to guarantee good air circulation for the condenser (see FIG. 11). Do not place objects
in front of the condenser protection grid, as this could interfere with the efficiency of the refrigerated cabinet (see FIG. 6).
Performance may suffer if the environmental conditions differ from those foreseen, or the cabinets are exposed to air
flows of more than 0.2m/sec or sources of heat.
To avoid this problem, the User should send the Manufacturer details of the environmental conditions before finalising the
design of the units, so that the technical parameters and material options can be modified and the installer informed of the
refrigerating power actually required.
5 - Electrical connections
Important: installation should be made following the manufacturer's instructions, by qualified personnel only, in conformity
with the electric safety regulations in force. Please refer to the electrical diagram in FIG.18a and FIG. 18b.
At the input of the supply it is necessary to install an omni-polar magnetothermic/differential device with contact opening
equal to 3 mm and adequate cut-off power.
Warning: Before connecting the unit to the mains, make sure that the mains voltage corresponds to that indicated on the
serial plate (bearing in mind that the max acceptable variations in voltage are +/- 10%). Check that the cable used has the
proper cross-section and length to withstand the current and the power absorbed by the combination, as indicated in
TAB. 1. The plug-in units are supplied already fitted with a 2,5 m cable and plug (see FIG. 7), so the unit must not be
installed more than 2,5 m from the nearest wall socket. The cabinet should be connected to its own fixed current socket
(i.e. without extension leads or multiple plugs). The cable should be fully extended and located where it is unlikely to be
struck, caught or stepped on, away from water and other liquids and heat sources and must not be damaged. In case of
breakage of the power cable of the cabinet, it must be replaced by the manufacturer or by institution in charge of it. The
plug must still be accessible even after installing the unit.
Warning: Follow the Manufacturer's instructions to install the unit, using qualified personnel and complying with the
electrical regulations for the specific country (electrical safety standards and laws, accident and fire prevention laws, EC
directives). Incorrect installation may cause injury and damage; the Manufacturer is not liable for this.
The unit must be earthed. The Manufacturer is not liable for any damage or injury should this safety regulation be
ignored. If the unit is to be installed far from the electrical sockets, suitable electrical connections are needed and these
must comply with the prevailing standards. The use of adapter plugs is strictly prohibited. The Manufacturer is not liable
for any damage or injury arising from incorrect installation.
17