Sport-thieme H700ST Instructions De Montage Et Utilisation page 8

The right-hand pedal, marked with the letter (R),
screws onto the right-hand crank (Q), also marked
with an (R), in a clockwise direction. Tighten securely,
Fig.4.
The left-hand pedal, marked with the letter (L), screws
onto the left-hand crank, also marked with an (L), in
an anti-clockwise direction. Tighten securely Fig. 4.
4. FITTING THE HANDLEBAR STEM.-
Connect the two terminals (C-8; 107) Fig.5, coming
out of the handlebar stem (12) and (C-16; 108) the
main body (40).
Insert the handlebar stem (12) onto the boss on the
main body (40) taking care not to pinch the cables.
Fit the bolts (13) and fl at washers, as shown in Fig.5,
align the handlebar stem and hand tighten.
5. FITTING THE BOTTLE HOLDER.-
Take the bottle holder (18), insert it in through the top
of the handlebar (12), Fig.6.
Next, release the screws (17) on the handlebar (12),
position the bottle holder and secure it by using the
screws (17) removed previously.
6. INSTRUCTIONS FOR FITTING THE
SADDLE.-
In order to raise or lower the saddle post (39), Fig.7,
first loosen off the control knob (41) on the saddle
post a little by turning it in an an- ticlockwise direction.
Pull the control knob back and without releasing it,
move the saddle post up or down.
Next, take the horizontal tube for the saddle (34) and
attach the saddle (33) to it, Fig.8, tighten the nuts (Z).
Now take the knob (59) off the horizontal saddle tube
(34), as shown in Fig.9, and place the horizontal tube
on the saddle post (39) lining up the hole with the nut
on the horizontal tube, insert the knob (59) and
tighten, Fig.10.
VERTICAL ADJUSTMENT.
In order to raise or lower the saddle post, fi rst loosen
off the control knob (41) on the saddle post a little by
turning it in an anticlockwise direction, pull the control
knob back and without releasing it, move the saddle
post up or down, Fig.10. When it is at the right height
release the knob and it will lock into a hole on the
saddle post. Tighten it up by turning the control knob
(41) in a clockwise direction.
HORIZONTAL ADJUSTMENT.
To adjust the saddle's horizontal position, loosen the
control knob (34) on the saddle's horizontal bar and
move the saddle, along with the bar, into the desired
position, then tighten the control knob securely,
Fig.10.
TILTING THE SADDLE.
The saddle can be tilted backward or forward. Loosen
off nut (Z) shown in Fig.10, located under the saddle,
tilt the saddle into the desired position and then
retighten the nut securely.
Do not adjust the tilt of the saddle while you are
still sitting on it.
7. FITTING THE MONITOR.-
Bring the monitor (2) to the handlebar stem (12)
Fig.11, connect the two terminals (107) coming out of
the handlebar stem (12) and (B-11) the monitor (2),
Fig.11.
Insert the monitor (2) onto the handlebar stem (12), as
shown in Fig.11, making sure not to pinch any of the
cables.
Fit the bolts (6) along with the flat washers, making sure
that the handlebar is aligned correctly, securely tighten
all of the bolts on the handlebar stem including the bolts
at the base which were left hand tight in point 4.
LEVELLING.-
Once the unit has been placed into its final position,
make sure that it sits fl at on the fl oor and that it is
level. This is achieved by screwing the adjustable foot
(28) up or down, Fig.12.
MOVEMENT & STORAGE.-
The unit is equipped with wheels (23) to make it
easier to move about. The two wheels at the front of
the unit make it easier to place the unit in any chosen
position, as shown in the Fig.13. Store it in a dry
place, preferably
temperature.
MAINS CONNECTION.-
Insert the jack (M) on the transformer (106) into the
connection hole (K) on the main body (40) (bottom,
rear of the machine) and then plug the transformer
into a 220 V mains supply, Fig.14.
THE MANUFACTURER RESERVES THE RIGHT TO
MODIFY THE
PRODUCTS WITHOUT PRIOR NOTICE
8
H700ST
not subject to changes
SPECIFICATIONS
in
OF ITS