Publicité
Les langues disponibles
Les langues disponibles
Thank you for purchasing this Whale® product. For over 60 years, Whale has led the way in the design and manufacture of freshwater
and waste systems including: pumps, plumbing faucets, showers for low voltage applications. The company and its products have built a
reputation for quality, reliability and innovation backed up by excellent customer service. For more information visit www.whalepumps.com.
1. SPECIFICATION
Model Number
Weight
Hose Connections
Materials
Materials in contact with fluid
Maximum Suction Lift
Maximum Discharge Head
2. TO THE USER
Read the following carefully before installation. WARNING: Please note that incorrect installation may invalidate the warranty.
3. TO THE INSTALLER
Check that the product is suitable for the intended application, follow these installation instructions and ensure all relevant personnel read
the points listed below. Also ensure that these operating instructions are passed on to the end user.
4. APPLICATION
This Compac 50 is designed for installation in recreational marine vessels only as a manual bilge pump. If it is intended for any other
purpose or with any other liquid, it is the user's responsibility to ensure that the pump is suitable for the intended use and, in particular, that
the materials are fully compatible with the liquids to be used. The Whale Compac 50 is not recommended for domestic applications.
5. WARNINGS
1.
With all applications, it is important that a system of safe working practice is applied to installation, use and maintenance.
The electric supply must be turned off and water system drained prior to installation.
2.
Not suitable for pumping flammable liquids, diesel, chemicals etc. Suitable for bilge water only.
3.
NOTE: Bilge pump capacities may not be sufficient to prevent flooding from rapid accumulation of water due to storms, rough
weather and/ or rapid leaks created by hull damage and or unsafe navigational conditions.
4.
In order to securely fasten the unit, ensure that the mounting surface is a minimum thickness of 5mm (3/16") (when fitted with the
screws supplied). NOTE Do not screw directly to the hull - must be mounted on a bulkhead or on an additional board.
Contact Whale® Support team for further technical advice: Tel: +44 (0)2891 270531
6. INSTALLATION
Note: Incorrect installation will invalidate warranty.
6.i Location
•
Choose a position to mount the pump that is dry and away from standing water and is
free from obstacles.
•
To maximize performance, mount in a position with the shortest possible pipe run lengths.
6.ii Installation
The Compac 50 is a covered diaphragm pump, designed specifically for low profile installation
below deck or thru bulkhead. The pump chamber complete with inlet/outlet hose connections, can
be rotated through 360° (Fig. 1) allowing complete flexibility in the choice of flow direction relative
to the handle position.
To change direction of pump flow: Slacken the clamping ring screws and rotate the pump
body to the desired positions. Re-tighten the clamping screws, (this can be adjusted even
after installation).
Inlet/Outlet Options: There are 4 possible hose directions for both inlet and outlet. These
can be combined to give 16 port orientations (see Fig 2).
To Change Inlet/Outlet Positions: Remove the 4 self-tapping screws from base of inlet/
outlet. Reposition the inlet/outlet, replace the 4 self-tapping screws and tighten.
Mounting the Pump
The Whale Compac 50 is provided with a deckplate. The hole positions are square, allowing a
choice of pump stroke direction, relative to the orientation of the deckplate.
1.
Using the deckplate as template, mark off and drill 4 x ¼" (6 mm) holes and cut out a 3 3/8" (86 mm) hole, which should be
central to the 4 x ¼" (6 mm) holes. Round off the edge of the hole to allow easy mounting of the rubber gaiter.
2.
Minimum deck thickness is 3/16" (5 mm). Deck can be reinforced up to a maximum of 5/8" (15 mm) by using a backing plate.
BP0350
0.9 kg (2 lbs)
25 mm (1") Smooth Hose Connections
Pump Body: Glass-filled Polypropylene, Clamp Ring: Acetal, Diaphragm, Valves and Seals: Nitrile®,
Operating Lever: Glass-filled Nylon, Gaiter: EPDM, Deck Plate Cover: PBT, Fasteners: Stainless Steel
Glass-filled Polypropylene, Nitrile®, Stainless Steel
3 m (10 ft)
4 m (13.5 ft)
Whale Compac 50
BP0350
Email: info@whalepumps.com
Clamping ring screws
Figure 1
Figure 2
Publicité
