Machine Preparation; Battery Charger Preparation; Battery Charger Installation And Connection; Battery Type - LAVOR Pro COMFORT M87 Manuel

battery poles, do not generate sparks and do not smoke.
The batteries are normally supplied full of acid solution
(for the Pb-Acid type) and ready for use. In any case,
follow the steps indicated in the manual supplied with
the battery and carefully follow the instructions regarding
safety and operating procedures.
6.2 BATTERY INSTALLATION AND PREPARATION
These operations must be carried out by specialised
personnel.
Make sure the two tanks are empty. If not, empty them
in accordance with the specific procedure.
Lift the recovery tank by 90°, making sure it is st able
in that position. This provides access to the battery
compartment from the top.
Disconnect the Anderson connector of the battery wiring
from the Anderson connector of the machine wiring.
Always hold the connectors with the hands and never
pull on the cables.
Attach the battery wiring to the battery, connecting
the terminals only on the poles marked with the
same symbol (red wiring "+", black wiring "-")! A
battery short-circuit may cause an explosion!
Run the cables toward the wiring outlet opening (on
one side of the box, only for Pb-Acid batteries), tighten
the terminals at the poles and cover them with V aseline.
Insert the battery putting the opening in the box (only
for the Pb-Acid battery) in a position to run the
electric wiring to the connector of the machine
MESSAGE ON THE DISPLAY
Charge curve
IUIa-Acd
IUIa-PzV Gel
IUIa-Acd
IUIa-PzV Gel
IUIa-Acd
IUIa-PzV Gel
If the battery charger and battery settings do
not correspond, do not connect or charge the battery
and follow the steps described below.
With the smart card(s) (optional) corresponding to the
battery being used or to be charged, program the battery
charger (as written in the corresponding manual and
on the front panel): insert the smart card into the special
battery charger slot, turn on the battery charger, wait
a few seconds, turn off the battery charger and remove
the card.
Without a smart card that corresponds to the battery
being used or to be charged, do not carry out any
operation and contact the authorised service centre.
Once the battery charger has been correctly
programmed, follow the procedure described in the
specific section.

6.5 MACHINE PREPARATION

Before starting to work, wear non-slip shoes, gloves
wiring.
After checking that all the controls on the panel are
in position "0" or at rest, connect the battery
connector to the machine connector.
recovery tank) making sure not to crush any wires.

6.3 BATTERY CHARGER PREPARATION

To use the battery charger, mount the connector shipped
with the machine on the battery charger -battery
connection wiring.
To assemble the connector, do the following:
- Remove about 13 mm of the protective sheath from
each of the two battery charger cables (red and black)
- Insert each cable into the metallic points/terminals of
the connector and press firmly using pliers.
-
into the connector, checking the polarity (red cable =
"+", black cable = "–").
6.4 BATTERY CHARGER INST ALLATION AND
CONNECTION
The battery charger is generally supplied ready to use
if requested with a specific battery. Make sure that the
battery charger was correctly programmed to charge
the battery supplied: when the machine is switched on,
the display will indicate the charge settings. Check the
voltage and charge current relative to the type of battery
according to the following table:
Voltage Amperage
24V 60A
24V 50A
36V 50A
36V 50A
36V 60A
36V 50A
and any other personal protection device indicated by
the supplier of the detergent used or considered
necessary based on the operating environment.
the relative sections for a detailed description of these
steps:
Check the battery charge level and charge, if necessary .
Mount the brushes or scraper disks (with the abrasive
disks) that are suitable for the surface and work involved.
Mount the squeegee, check that it is solidly att ached
and connected to the suction hose and that the drying
straps are not too worn.
Make sure that the recovery tank is empty. If not, empty
it completely.
Check and completely close the detergent solution
release control.
Fill the detergent solution tank with a mix of clean water
and non-foaming detergent in an adequate concentration
through the rear hole. Leave 7 cm between the mouth
Close the battery compartment (lowering the
Now insert the terminals (connected to the wires)

BATTERY TYPE

24V 525Ah Pb-Acid
24V 400Ah Gel
36V 420Ah Pb-Acid
36V 320Ah Gel
36V 525Ah Pb-Acid
36V 400Ah Gel
Do the following before starting to work. Refer to
29