Important; General Characteristics - Astralpool 32382 / 36655 Manuel D'installation

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 8
ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the Mini light for swimming pool, follow the instructions provided below:
1. VERIFY THE CONTENTS OF THE PACKING:
The following accessories are included inside the box:
Concrete pool floodlamp, model 32382 / 36655
Housing body
Floodlamp unit
Bag of screws:
1 DIN 912 A2 M-4x12 screw
6 DIN 966 A2 M-6x24 Punt. Screws
2 gland seal adapter
Panelled pool with Liner floodlamp, model 34185 / 36659
Housing body
2 watertight joints
Floodlamp unit
Bag of screws

2. GENERAL CHARACTERISTICS:

This floodlamp has been designed to be used fully submerged underwater in fresh water. It is a Class III electric apparatus
with very low safety voltage (12 V with alternating current).
The floodlamp complies with IPX8 degree of protection (resistance to penetration of dust, solid bodies and humidity) at a
nominal immersion depth of 2 m.
This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS
PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.
The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric components
which have been inserted or handled at locations other than its own premises.
3. INSTALLATION:
• In order to clearly light a pool it is recommended to install a floodlamp every 5 m
which are especially deep, a floodlamp is required for every 10 m
• In order to prevent glare, the floodlamps should be installed so that they face away from the residence or usual view of
the swimming pool.
• In the event that lighting is used in training or competition pools, the floodlamps should be installed on the sides to
prevent glare on the swimmers.
• To avoid emptying the pool if the projector has to be handled, it is recommended to install it in places which are
accessible from the upper edge of the pool.
Prior to installation verify that the gland seal has been fully tightened.
The floodlamp should be placed on the wall of the pool at approximately 400-700 mm from the water surface (Fig. 1). The
crosshead and the clamp must be placed so that that the word "TOP" is located on the upper part
The method of fastening the crosshead mount to the pool wall varies depending on whether it is a floodlamp for concrete
pools (model 32382) or prefabricated pools (model 32383)
Concrete swimming pool (Model 32382 / 36655)
To install a floodlamp in a concrete pool the housing (nº11) should be fixed in the wall of the swimming pool (Fig.1). Use
eight M6x24 (n21) screws to secure the housing clamp to the pool.
Prefabricated swimming pool (Model 32383 / 36657)
To install a floodlamp in prefabricated swimming pool make a circular hole with a diameter of 110 mm (Fig. 2).
Install the housing and one of the joints on the outer side of the pool. Install the other joint (no. 3) on the inner side and
use two cylindrical screws (no. 21) to secure the three components (Fig 3). Make sure that the cable outlet of the housing
remains on the upper part.
To install the housing clamp (no. 2) on the inner side of the swimming pool, make sure that the cylindrical heads of the
screws (no. 21) which have been installed previously coincide with the area reserved for them on the back part of the clamp
(Fig 4).
Use eight 6 x 24 screws (no. 21) to secure the clamp to the wall of the pool (Fig 5). Make sure that the word "TOP" is
located on the upper part.
Prefabricated pool floodlamp, model 32383 / 36657
Housing body
2 watertight joints
Floodlamp unit
Bag of screws
2 DIN 7981 A2 4,8x16 screws
1 DIN 912 A2 M-4x12 screw
6 DIN 966 A2 M-6x24 Punt. Screws
2 gland seal adapter
3
of water volume.
-2-
2
of water surface. In swimming pools

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

32383 / 3665734185 / 36659

Table des Matières