Vs-Fhp Pump Dip Switch Settings; Remove Pump Lid - Zodiac Jandy VS FloPro VS-FHP Série Guide D'installation Et De Fonctionnement

Page 12
ENGLISH
To install an AquaLink
later) or an AquaLink PDA (Rev 4.0 or later):
1. Remove power from the VS-FHP pump by
disconnecting the high voltage lines or by opening
any breaker to which the VS-FHP pump power is
connected.
wARNING
ELECTRICAL SHOCK HAZARD
Turn off all switches and the main breaker in the
VS-FHP pump electrical circuit before starting the
procedure. Failure to comply may cause a shock
hazard, resulting in severe personal injury or death.
2. Slide dip switches 1 and 2 down, so they are in the
OFF position. See Figure 5.
3. Select the desired address(es) for the
pump by setting dip switches 3 and/or 4, as shown
in Section 3.3, VS-FHP Pump Dip Switch Settings.
4. Connect the other end of the cable to an RS-485
connector on the AquaLink RS (or multiplexer
interface board), matching wire colors with
connector positions
3-yellow, and 4-green. See Figure 5.
5. Restore power to the VS-FHP pump and verify the
operation of the controller.
6. Refer to the appropriate manual to operate the
pump: AquaLink RS Owner's Manual, 6593, or
AquaLink PDA Owner's Manual, H0572300.
3.3

VS-FHP Pump Dip Switch Settings

As shown in Figures 4 and 5,
switch is located at the rear of the VS-FHP pump. This
dip switch serves two (2) functions: it selects the pump
address, and it determines what type of controller will
be used with the pump. The tables below show the dip
switch settings.
Switch Switch Controller
1 2
OFF OFF AquaLink RS or AquaLink PDA
ON OFF AquaLink RS or AquaLink PDA
OFF ON AquaLink RS or AquaLink PDA
ON ON Variable Speed
Switch 3 Switch 4 Pump Address
OFF OFF PUMP 1
ON OFF PUMP 2
OFF ON PUMP 3
ON ON PUMP 4
Jandy ® FloPro™ Variable-Speed Pump Series VS-FHP
RS controller (Rev O or
®
VS-FHP
as follows: 1-red, 2-black,
the 4-position dip
Controller JEP-R
|
3.4

Remove Pump Lid

1. Make sure that the pump is turned off.
2. Make sure that the switch to the circuit breaker
that powers the pump motor is turned off.
wARNING
ELECTRICAL SHOCK HAZARD
Turn off the pump and the main breaker in the pump
electrical circuit before starting the procedure. Failure
to comply may cause a shock hazard, resulting in
severe personal injury or death.
wARNING
ELECTRICAL SHOCK HAZARD
Due to the potential risk of fire, electric shock, or
injuries to persons, Zodiac
in accordance with the National Electrical Code
(NEC), all local electrical and safety codes, and
the occupational Safety and Health Act (OSHA).
Copies of the NEC may be ordered from the National
Protection Association, 470 Atlantic Ave., Boston,
MA 02210, or from your local government inspection
agency.
In Canada, Zodiac Pumps must be installed in
accordance with the Canadian Electrical Code
(CEC).
AquaLink RS
RS-485 Connectors
S1
S2
4-Position
DIP Switch
Figure 5. wiring AquaLink RS Controller or
AquaLink PDA to VS-FHP Pump
Installation and Operation Manual
® Pumps must be installed
4 3 2 1 4 3 2 1 6 5 4 3 2 1 10 9 8 7 6 5 4 3 2 1
RS6 & RS8 ONLY RS8 ONLY
RESET POOL MODE
SPA MODE
AUTO
SPA DRAIN
SERVICE
HEATER SOLAR
TIME OUT SPA FILL
Connect to
AquaLink RS
RS-485 Connector
4 3 2 1
(or Multiplexer
Interface Board)
Variable-Speed
Pump