Fender HOT ROD De Ville Mode D'emploi page 7

T. POWER CORD - Connect the power cord in
accordance with the voltage and frequency ratings
listed on the rear panel of the unit.
U. FUSE - The fuse protects the unit from electrical
faults. Replacement fuses must match the type and
rating specified on the fuse holder.
repeatedly blows fuses, have the unit tested at an
authorized Fender ® Service Center.
V. MAIN SPEAKER - One of the following speaker load
configurations (internal or external) must always be
connected as shown below, when the unit is on:
DeVille 410
V. W.
1. 1.
2. 2.
*
3. 3.
*Insert an open plug (no speakers connected) for this
configuration.
TYPE:
PART NUMBERS:
POWER REQUIREMENT:
POWER OUTPUT:
INPUT 1/2 IMPEDANCES:
PRE-AMP OUTPUT IMPEDANCE:
POWER-AMP INPUT SENSITIVITY:
POWER-AMP INPUT IMPEDANCE:
TUBES:
*(Tube label color: Red=1, White=2, Blue=3)
FUSE:
SPEAKER:
FOOTSWITCH:
DIMENSIONS HEIGHT:
WIDTH:
DEPTH:
WEIGHT:
w w w w w w . . f f e e n n d d e
Fender ® Hot Rod™ DeV
Fender ® Hot Rod™ DeV
If the unit
DeVille 212
V. W.
*
2
HOT ROD DEVILLE 410
PR 247
021-3201-000 (120V, 60Hz) USA
021-3231-000 (240V, 50Hz) AUS
021-3241-000 (230V, 50Hz) UK
021-3261-000 (230V, 50Hz) EUR
021-3271-000 (100V, 50/60Hz) JPN
180W
60W into 8Ω or 4Ω at 5% THD
1 MΩ / 136 kΩ
1.5 kΩ Max
200 mV for clipping
54 kΩ
Three Fender Groove Tube GT12AX7 (099-4005-000)
Two Fender Groove Tube GT6L6B (099-4401-*02)
3A 250V fuse (100V and 120V versions)
1.6A 250V fuse (230V and 240V versions)
Four 10" 8Ω Fender Model V 1030
Special Design (048832)
2 Button: Gain, Channel (050419)
23.5 in (59.7 cm)
23.5 in (59.7 cm)
10.75 in (26.7 cm)
50 lb (22.5 kg)
Product specifications are subject to change without notice.
e r r . . c c o o m m
ille/DeV
ille/DeV
W. EXTERNAL SPEAKER - This jack is wired in parallel
with the main speaker jack and must only be used
with something connected to the main speaker jack
as shown in the MAIN SPEAKER {V} description
above.
X. FENDER ® /GROOVE TUBES™ GT6L6B - The
output tubes in your new Hot Rod™
amplifier are performance matched and
labeled as a color-coded pair.
replacing these tubes, we recommend
selecting new tubes that have the same red, white or
blue color labels as the originals. Otherwise, tube
bias may need adjustment.
below for your color coded part number.
Y. PREAMP TUBE STABILIZER -
A vibration–absorbing stabilizer is
installed around the preamp tubes to
minimize tube microphonics that
normally develop over time. The stabilizer can be
used with all preamp tubes compatible with your
Hot Rod™ amplifier.
Specifications
Specifications
HOT ROD DEVILLE 212
PR 247
021-3200-000 (120V, 60Hz) USA
021-3230-000 (240V, 50Hz) AUS
021-3240-000 (230V, 50Hz) UK
021-3260-000 (230V, 50Hz) EUR
021-3270-000 (100V, 50/60Hz) JPN
180W
60W into 4Ω or 2Ω at 5% THD
1 MΩ / 136 kΩ
1.5 kΩ Max
200 mV for clipping
54 kΩ
Three Fender Groove Tubes 12AX7A (099-4005-000)
Two Fender Groove Tubes GT6L6B (099-4401-*02)
3A 250V fuse (100V and 120V versions)
1.6A 250V fuse (230V and 240V versions)
Two 12" 8Ω Fender Re-issue
Gold Label (037617)
2 Button: Gain, Channel (050419)
21 in
24.25 in
10.75 in
53.5 lb
w w w w w w . . m m r r g g e
ille 212
ille 212
See Specifications
(53.3 cm)
(61.6 cm)
(27.3 cm)
(24.2 kg)
e a a r r h h e e a a d d . . n
7
When
n e e t t