Before Starting The Equipment - EINHELL GE-WS 18/150 Li Instructions D'origine

The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective mask is
used.
2. Contact with hazardous substances. Spray
materials can be harmful if inhaled or swal-
lowed or if allowed to come into contact with
the skin or eyes. Follow the instructions and
wear suitable protective equipment.
Danger!
This electric power tool generates an electro-
magnetic fi eld during operation. Under certain
circumstances this fi eld may actively or passively
impede medical implants.
To reduce the risk of serious or fatal injuries, we
recommend persons with medical implants to
consult their doctor and the manufacturer of the
medical implant prior to using the equipment.

5. Before starting the equipment

Warning!
Switch the equipment off and remove the battery
before carrying out any assembly work.
Anl_GE_WS_18-150_Li_SPK9.indb 24
GB
5.1 Assembling the spray tube and hose
Screw the spray tube onto the spray gun handle
(Fig. 3).
Important! Always check the hose connections.
Any leaks must be remedied immediately and the
equipment must not be used until this has been
done.
5.2 Fitting the harness (Fig. 3a - 3b)
Attach the fastening hooks for the harness (Item
10c) to the container on the left and right sides
(see also Fig. 9).
5.3 Preparing spray solution and fi lling the
container
Switch off the equipment and remove the battery.
Note:
•
Always follow the manufacturer's instructions
when mixing spray solutions. Fill the tank only
with the amount of solution you intend to use.
•
Observe the quantities to be used as listed by
the manufacturer of the solution.
•
Spray solution must have a water-like consis-
tency.
•
The spray container can be filled with a maxi-
mum 15 liters of liquid.
•
Pesticides must only be prepared outdoors
and never in living quarters, stables, or sto-
rage rooms for food and animal feed.
•
Spray solutions can be prepared in a sepa-
rate container and mixed thoroughly before
being filled into the container of the pressure
sprayer.
•
If you intend to use organic spray solutions,
they must be filtered prior to filling the sprayer.
•
The solution must always be filled in through
the filling sieve situated in the tank (Fig. 4 /
Item 7a).
•
Clean the equipment immediately after each
use. This is the only way to keep the liquid-
carrying parts clean and prevent clogging.
Clogged components can lead to defects.
1. Place the pressure sprayer on a level surface.
Unscrew the tank lid (Fig. 5 / Item 6) from the
tank. On the inside of the tank lid you will see
measuring ranges with 5ml, 10ml and 25ml
contents.
2. Pour the amount of liquid (e.g. water) spe-
cifi ed by the solution manufacturer into the
spray container. If the spray solution has not
been prepared ready for spraying, add the
measured quantity of concentrated additive
and close the container carefully.
- 24 -
22.10.2020 08:47:06