Electrical Safety; Assembling Stand - ATIKA ASP 5 N-UG Mode D'emploi

Take a working position, which is behind the slide of the
area of the operating lever. Never stand in the splitting
wedge's zone.
Never stand on top of the machine.
Pay attention at all times. Take care with what you are
doing, and approach the work sensibly. Do not use the
machine:
− when you are tired.
− under the influence of drugs, alcohol or medications
that may impair your powers of judgement.
When working with the machine, always wear
− protective goggles or face mask
− safety gloves
− ear protection, if necessary
− safety shoes with steel toe-caps
Wear suitable work clothing:
− do not wear any loose-fitting clothing or jewellery, since
these may be caught or trapped by moving parts
Within his area of work the operator is responsible for
third parties.
The machine may not be operated by children or young
people under the age of 18.
Keep children away form machine.
Never operate the machine if other persons are in the
immediate vicinity.
Never leave the saw unattended.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on
the machine that could impair the safety.
Faulty or damaged parts in the device must be replaced
immediately.
Do not spray machine with water
(this is hazardous due to live components).
Do not leave the machine standing in the rain or use
when raining.
Store the unused machine in a dry locked place away
from the reach of children.
Switch the machine off and remove the mains plug from
the socket when
− carrying out repair works
− carrying out servicing and repair works,
removal of faults
− Transporting
− leaving unattended (even during short interruptions)
Check the machine for possible damage
Before continuing to use the machine, the protective
−
devices must be inspected to ensure that they work
perfectly and with their intended function
Check whether the parts are damaged. All parts must
−
be correctly installed and fulfil all conditions to ensure
perfect operation of the saw
Damaged guards and parts must be properly repaired
−
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
14
Damaged or illegible safety warning labels should be
−
replaced immediately.

Electrical safety

Electrical connections must conform to IEC 60245 (H 07
RN-F) with a cable cross-section of at least
⇒ 1.5 mm² for a maximum cable length of up to 10 m
Never use the machine with a power supply cable of over
10 m in length. Longer power supply cables will cause a
drop in voltage. The motor will not be able to provide its
maximum performance and the operation of the machine
will be impaired.
When laying the connecting attachments, be sure that
they do get crushed or bent, and that the plug-and-socket
connection does not get wet.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
When working outdoors, only use extension cables
especially approved and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified
electrician or one of our customer service points. Local
regulations – especially regarding protective measures –
must be observed.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.
A s s e m
A s s e m
Please observe the enclosed assembling
instructions!
Connect the firewood splitter to the power supply system
only after having finished the complete assembly.
Two persons are required for assembly.
Removing the wheels
2 On both sides, remove the hubcap (13) from the
wheel (12).
3 Remove also the circlip on both sides.
4 Pull off the wheels (12) from the axle.
b l i n g S t a n d
b l i n g S t a n d