Button Function - AEG X99384MDO Mode D'emploi

9
GB - USE
USE
A

Button Function

A Hood Functions On/Off
B
Manages motor speed:0--
V1--V2--V3--V4--P
C
Delay function
Enables / Disables the
Remote Control Receiver.
D
Sensor
E
Manages Lighting
Intensity:0--L1--L2--L3-
-LMax
F
Filter ResetResets the
Filter Saturation alarm
when the button is tou-
ched with the motor and
lighting turned off.
Enables/Disables the
Activated Charcoal Filter
Alarm.
After connecting the hood to the mains, the commands are activated after 4seconds. When the Hood is switched off, none of the fun-
ctions is displayed, and only the normal lettering on the control panel is visible. All the rest will light up (intensity 50%) when button A
is touched. The controls are activated by touching the selected function, which will light up more brightly (intensity 100%) with respect
to the other hood functions (intensity 50%). When no commands are given for at least 10 seconds, only the selected functions will be
lighted (Intensity 100%) and all the rest will turn off (Intensity 50%). After 7 hours in operation, if no further commands are given the
hood will switch off (Motor Off + Lights Off), from here you can touch for activated the function, and the next touch you can select the
desired function.It is possible to activate one of the hood functions (Speed and Lighting) not just by touching the control panel, but also
by placing a finger on the panel and sliding it towards the chosen function without lifting it off. If the motor and lights are turned off, by
setting them to zero, all the command LEDs will remain on at 50%, and if no further commands are given in the next 10 seconds, then all
the LEDs will be turned off with the exception of the "0" LEDs, which will remain on for a further 15 minutes.
B C
Specifications
When the button is touched with the hood turned off, all functions light up
(intensity 50%) and are enabled.
When the button is touched with the hood in operation, all functions are turned
off and disabled (Motor Off + Lights Off).
When the area is touched, the motor starts at the speed required.
P = Intensive Speed, timed for 5 minutes, after which the system returns to the
previous speed. When activated from Motor Off it returns to speed V1.When
the required speed is touched, it will become brighter (intensity 100%) than the
other functions (intensity 50%).
Touching this button activates automatic shutdown of the Motor, the Fans and
the Lighting with a 10 minute delay. It can only be activated with the motor on,
running at any speed except Intensive, and with the Sensor = Off.
When this button is pressed and held for 4 seconds (Motor Off + Lights Off, in
the absence of other alarms, the Led will light up for:
4 seconds to indicate that the Remote Control has been Activated
2 seconds to indicate that the Remote Control has been Deactivated
In this mode the Hood operates automatically for a maximum of 5 hours, after
which it switches the Motor off. The hood modifies the speed of the motor
according to the findings of the sensor.
Buttons B and C do not work. The function is disabled by pressing the Button or
turning the hood off.
When this area is touched, the Lights turn on at the required intensity.
When the lighting intensity is touched, it will become brighter (intensity 100%)
than the other functions (intensity 50%).
After 100 hours operation the Led lights up continuously to indicate saturation
of the Metal Grease Filters.After 200 hours operation the Led flashes to indicate
saturation of the Activated Charcoal Filters.
When this button is pressed and held for 4 seconds(Motor Off + Lights Off), in
the absence of other alarms, the Led will light up for:
4 seconds to indicate that the Activated Charcoal Filter Alarm has been activated
2 seconds to indicate that the Activated Charcoal Filter Alarm has been deacti-
vated
D E F