Brandt UM1811 Guide D'installation Et D'utilisation page 33

1 1 / / INSTALLATION
ALLATION
D D E E S S C C R R I I P P T T I I O O N N O O F F Y Y O O U U R R A A P P P P L L I I A A N N C C E E
( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e m m o o d d e e l l ) )
B B
B
A A
Control panel and indicator lights
B B
Freezing drawers (1 or 2, depending on the model)
C C
Vegetable compartment
A A
A
C
C C
R R E E V V E E R R S S I I N N G G T T H H E E D D I I R R E E C C T T I I O O N N T T H H E E D D O O O O R R S S
O O P P E E N N
You can alter the direction in which the doors open if you wish:
T T h h e e a a p p p p l l i i a a n n c c e e m m u u s s t t a a l l w w a a y y s s b b e e d d i i s s c c o o n n n n e e c c t t e e d d f f r r o o m m t t h h e e p p o o w w e e r r
s s u u p p p p l l y y w w h h e e n n c c h h a a n n g g i i n n g g t t h h e e d d i i r r e e c c t t i i o o n n t t h h e e d d o o o o r r s s o o p p e e n n . .
• Gently tilt the appliance backwards and wedge it in this position.
• Remove the pin from the lower hinge and then remove the door.
Remove the lower hinge and fit it on the opposite side.
• Unscrew the upper hinge and fit this on the opposite side.
• Take the plastic guide off the hinge pin for the upper hinge and
press it into the opposite hole after removing the hole cover, which
is subsequently placed over the hole you have just created.
• Slide the door onto the pin for the upper hinge and close it.
• Insert the pin for the lower hinge and screw it down tightly.
• If your appliance is fitted with a vertical handle, ensure that you
move it over to the opposite side.
F F I I T T T T I I N N G G T T H H E E D D O O O O R R H H A A N N D D L L E E S S
( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e m m o o d d e e l l ) )
The handles are located inside the refrigerator. Fit the handles on
the doors, positioning them opposite the respective holes and fas-
ten them with the screws provided as shown in the diagram below.
Once the handles are in place, insert the screw covers supplied in
the spaces provided for this purpose
R R E E M M O O V V I I N N G G T T H H E E R R E E M M O O V V A A B B L L E E T T O O P P
( ( d d e e p p e e n n d d i i n n g g o o n n t t h h e e m m o o d d e e l l ) )
To install your appliance under a worktop, you may need to remove
its top.
T T h h e e a a p p p p l l i i a a n n c c e e m m u u s s t t a a l l w w a a y y s s b b e e d d i i s s c c o o n n n n e e c c t t e e d d w w h h e e n n y y o o u u p p r r o o - -
c c e e e e d d t t o o r r e e m m o o v v e e t t h h e e r r e e m m o o v v a a b b l l e e t t o o p p . .
• Remove the two screws at the back of the top.
• Free the top by lifting it at the back and sliding it gently forwards.
0 0 5 5
EN