Publicité
Les langues disponibles
Les langues disponibles
Overview
1 IR sensor for the remote control signals
2 LEDs IN 1 – IN 3 to indicate the input selected (8)
3 Button "Switch" to select an input
4 LED , lights up when the signal switch has
been switched off
5 Button /I to switch on and off
6 Connection for the power supply unit
1
IR
IN1
HDMI™ Signal Switch
These instructions are intended for users without any
specific technical knowledge. Please read the instructions
carefully prior to operation and keep them for later ref-
erence.
1 Safety Notes
The units (signal switch and power supply unit) corre-
spond to all relevant directives of the EU and are therefore
marked with
.
WARNING The power supply unit uses dangerous
mains voltage. Leave servicing to skilled
personnel only. Inexpert handling may
result in electric shock.
•
The units are suitable for indoor use only. Protect them
against dripping water, splash water and high air hu-
midity. The admissible ambient temperature range is
0 – 40°C.
•
Do not place any vessel filled with liquid on the unit,
e. g. a drinking glass.
•
The heat produced inside the signal switch must be dis-
sipated via the air vents; therefore, never cover the air
vents.
•
Immediately disconnect the power supply unit from the
socket
1. if the power supply unit or the signal switch is visibly
damaged,
2. if a defect might have occurred after the unit was
dropped or suffered a similar accident,
3. if malfunctions occur.
In any case, the units must be repaired by skilled per-
sonnel.
•
For cleaning only use a dry, soft cloth; never use water
or chemicals.
•
No guarantee claims for the units and no liability for any
resulting personal damage or material damage will be
accepted if the units are used for other purposes than
originally intended, if they are not correctly connected
or operated, or if they are not repaired in an expert way.
If the units are to be put out of operation de-
finitively, take them to a local recycling plant
for a disposal which is not harmful to the en-
vironment.
Never put batteries in the household waste. To protect
the environment, always take them to a special waste
disposal, e. g. collection container at your retailer.
2
3 4 5
IN2 IN3 Switch
/I
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright
©
by MONACOR INTERNATIONAL. All rights reserved.
7 Signal output HDMI OUT
8 Signal inputs HDMI IN 1 – 3
9 Buttons
OFF and ON
10 Buttons 1 – 3 for direct selection
of an input (8)
11 Input selector buttons
(as an alternative)
6
7
8
HDMI OUT
HDMI IN3
DC 5V
2 Applications
This signal switch allows you to connect three video signal
sources (DVD player, laptop, satellite tuner etc.) with a res-
olution up to "4K Ultras HD" to a display unit (monitor, TV
set, projector). The desired signal source can be selected on
the signal switch or via remote control.
3 Operation
1) The remote control is operated by means of a 3 V button
cell (type CR 2025). If the remote control is supplied
with a battery inserted, remove the protective film (to
protect the battery from being discharged) from the
battery holder. The remote control is now ready for op-
eration. When you press a button on the remote control,
always point the remote control at the IR sensor (1).
There must be no obstacles between the sensor and
the remote control.
To insert or replace the battery, pull out the battery
holder on the rear. Insert the battery with the positive
pole facing up. If the remote control is not in use for
a longer period of time, always remove the battery to
prevent damage due to battery leakage.
2) Connect the signal sources to the jacks HDMI IN (8).
Connect the display unit to the jack HDMI OUT (7).
3) Connect the power supply unit provided to the jack DC
5V (6) and to a mains socket (230 V/ 50 Hz).
4) Use the button /I (5) or ON (9) to switch on the signal
switch. The LED IN (2) of the most recent input selected
(8) will light up.
5) To switch to another input, press the button Switch (3) or
press 1, 2, 3 (10), ⋀ or ⋁ (11) on the remote control.
6) After operation, use the button
switch off the signal switch. The LED
If the signal switch is not in use for a longer period of
time, disconnect the power supply unit from the socket.
It will consume some power even when the signal
switch has been switched off.
4 Specifications
Max. signal resolution: . . . UHD (4K), supporting HDR
Number of inputs: . . . . . . . 3
Connections: . . . . . . . . . . . HDMI jacks, type A
Power supply: . . . . . . . . . . via power supply unit provided
Ambient temperature:. . . . 0 – 40 °C
Dimensions (W × H × D): . 111 × 21 × 53 mm
Weight: . . . . . . . . . . . . . . . 154 g
Subject to technical modification.
8
8
HDMI IN2
HDMI IN1
/I (5) or OFF (9) to
and connected to 230 V/5 0 Hz
A-1944.99.01.11.2018
OFF
ON
9
1
2
3
10
11
−HDMI SWITCH−
(4) will light up.
Publicité
