Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
19. On rooftops and other high locations, nail as
you move forward. It is easy to lose your
footing if you nail while inching backward.
When nailing against perpendicular surface,
nail from the top to the bottom. You can
perform nailing operations with less fatigue by
doing so.
20. A nail will be bent or the tool can become
jammed if you mistakenly nail on top of
another nail or strike a knot in the wood. The
nail may be thrown and hit someone, or the
tool itself can react dangerously. Place the
nails with care.
21. Do not point the ejection port at anyone in the
vicinity. Keep hands and feet away from the
ejection port area.
Never carry the tool with your finger on the trigger
•
or hand it to someone in this condition. Accidental
firing can be extremely dangerous.
22. Handle the tool carefully, as there is high
pressure inside the tool that can be dangerous
if a crack is caused by rough handling
(dropping or striking). Do not attempt to carve
or engrave on the tool.
23. Stop nailing operations immediately if you
notice something wrong or out of the ordinary
with the tool.
Always remove the fuel cell, the battery cartridge
•
and all of the nails:
−
When unattended.
−
Before performing any maintenance or repair.
−
Before cleaning a jam.
−
Before moving the tool to a new location.
24. Perform cleaning and maintenance right after
finishing the job. Keep the tool in tip-top
condition. Lubricate moving parts to prevent
rusting and minimize friction-related wear.
Wipe off all dust from the parts.
25. Do not modify tool without authorization from
Makita.
26. Do not attempt to keep the trigger or contact
element depressed with tape or wire. Death or
serious injury may occur.
27. Always check contact element as instructed in
this manual. Nails may be driven accidentally if
the safety mechanism is not working correctly.
28. Ask Makita's Authorized service centers for
periodical inspection of the tool.
29. To maintain product SAFETY and RELIABILITY,
maintenance and repairs should be performed
by Makita Authorized or Factory Service
Centers, always using Makita replacement
parts.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
IMPORTANT SAFETY
INSTRUCTIONS
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5.
Do not short the battery cartridge:
(1)
Do not touch the terminals with any
conductive material.
(2)
Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3)
Do not expose battery cartridge to water
or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.
6.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).
7.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8.
Be careful not to drop or strike battery.
9.
Do not use a damaged battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
Charge
the
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
2.
Never
recharge a fully charged
cartridge.
Overcharging shortens the battery service life.
5
battery
cartridge
ENC009-1
before
battery
Publicité
Table des Matières
