Table des Matières
Publicité
Level Plus
SoClean
®
®
Manuel d'utilisation
13.5 ATEX et IECEx
13.5.1 Sécurité intrinsèque
13.5.1.1 Conditions d'utilisation spéciales
1. Le boîtier de l'appareil contient de l'aluminium et peut constituer
un risque potentiel d'inflammation par impact ou friction. Prendre
toutes les précautions pendant l'installation et l'utilisation pour
MTS TO PRINT
éviter les risques d'impact ou de friction. (En cas d'installation
dans le cadre d'une Approbation GA)
MODEL NO.
2. La température ambiante maximale autorisée du transmetteur
SERIAL NO.
de niveau numérique/analogique Level Plus
éviter les effets de la température du processus et d'autres effets
DATE CODE.
thermiques, s'assurer que la température ambiante autour et dans
le boîtier du transmetteur ne dépasse pas 71 °C.
3. Certains modèles contiennent des pièces du boîtier de fabrication
autre que métallique, pour éviter le risque d'étincelle électrostatique, la
surface non-métallique ne doit être nettoyée qu'avec un tissu humide.
8 POINT TEXT
13.5.1.2 Étiquettes
ENTITY PARAMETERS:
SEE PRINT REFERENCE CHART
B
MTS Systems Corporation
Sensors Division
3001 Sheldon Dr.
SERIAL NO./DATE CODE
Cary, NC 27513
Model No:
Serial No:
Date :
NOTES:
1. STANDARD LETTERING UNIVERS 55
FM14ATEX0068X
OR ITC GARAMOND BOOK.
IECEx FMG 14.0032X
B
2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN
BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.
∆
3.
INDICATES CRITICAL DIMENSIONS.
SERIAL NO./DATE CODE
when connected in accordance
with FM approved installation
4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES
drawing # 651543-3
5. MATERIAL: .8 [.03] THICK ALUMINUM
6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.
WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
Fig. 51 : Étiquette FMC sécurité intrinsèque, Modbus ou DDA, boîtier NEMA
69.85 [2.75]
NOTES:
1. STANDARD LETTERING UNIVERS 55
A
OR ITC GARAMOND BOOK.
2. MATERIAL TO BE SCREEN PRINTED ALUMINUM WITH SATIN
BACKGROUND AND BLACK TEXT OR LASER ETCHED ALUMINUM.
∆
3.
INDICATES CRITICAL DIMENSIONS.
4. DIMENSIONS IN BRACKETS [ ] ARE IN INCHES
IP RATING WAS 66
5. MATERIAL: .8 [.03] THICK ALUMINUM
6. REFER TO TABLE 1 FOR "L1" & "L2" DIMENSIONS.
RELEASE TO PRODUCTION
2
USE MTS LOGO
ARTWORK
10 POINT SIZE
4.5 POINT TEXT SIZE
est de 71 °C. Pour
®
SIZE
®
Level Plus Transmitter
MTS TO PRINT
MODEL NO.
***NO REVISIONS SHALL BE MADE WITHOUT THE
B
12.70 [.50]
3.70 [.15]
A
1725
REV
MTS TO PRINT
MODEL NO.
II 1/2 G Ex ia IIC T4 Ga/Gb
PROPRIETARY DATA
Ta = -50°C to +71°C ; IP65
THE INFORMATION AND DESIGN(S) DISCLOSED
HEREIN ARE THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY FORM
EXCEPT AS GRANTED IN WRITING BY MTS
***NO REVISIONS SHALL BE MADE WITHOUT THE NOTIFICATIO
P/N 551629-3 Rev B
SYSTEMS CORPORATION. THIS RESTRICTION
EXCLUDES INFORMATION THAT IS IN THE
C
3.70 [.15]
12.70 [.50]
PUBLIC DOMAIN OR WAS LEGITIMATELY IN THE
B
PRIOR POSSESSION OF THE RECIPIENT.
A
2
R
E
V
PROPRIETARY DATA
THE INFORMATION AND DESIGN(S) DISCLOSED
HEREIN ARE THE PROPERTY OF MTS SYSTEMS
CORPORATION AND MAY NOT BE USED,
REPRODUCED OR DISCLOSED IN ANY FORM
EXCEPT AS GRANTED IN WRITING BY MTS
SYSTEMS CORPORATION. THIS RESTRICTION
EXCLUDES INFORMATION THAT IS IN THE
MTS Systems Corporation
Sensors Division
3001 Sheldon Dr.
Cary, NC 27513
Model No:
Serial No:
Date :
2
R3.30 [.13]
WARNING: REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
Fig. 52 : Étiquette ATEX/IECEx sécurité intrinsèque, Modbus ou DDA, boîtier NEMA
28.70 [1.13]
2
1.78 [.07]
R
MTS Systems Corporation
Sensors Division
3001 Sheldon Drive, Cary, N.C. 27513
15.80 [.62]
7847
IP RATING WAS 66
II 1/2 G Ex ia IIC T4 Ga/Gb
Ta = -50°C TO +71°C ; IP65
WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY
REFER TO INSTALLATION DRAWING FOR CAUTION/WARNINGS
7570
RELEASE TO PRODUCTION
Fig. 53 : Étiquette ATEX/IECEx sécurité intrinsèque, Modbus ou DDA, boîtier à cavité simple
ECO #
ou double
34.69 [1.37]
R
MTS Systems Corporation
Sensors Division
1.78 [.07]
3001 Sheldon Drive, Cary, N.C. 27513
II 1/2 G Ex ia IIC T4 Ga/Gb
8256
Ta = -50°C TO +71°C ; IP65
WARNING: SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY
REFER TO INSTALLATION DRAWING FOR CAUTION/WARNING.
7
8
4
7
7570
Fig. 54 : Étiquette ATEX/IECEx sécurité intrinsèque, Modbus ou DDA, boîtier à cavité simple
ou double
E
C
O
#
I
46
I
8 POINT TEXT
SIZE
®
Level Plus Transmitter
FM14ATEX0068X
IECEx FMG 14.0032X
II 1/2 G Ex ia IIC T4 Ga/Gb
Ta = -50°C to +71°C ; IP65
"L1"
when connected in accordance
with FM approved installation
drawing # 651543-3
∆
"L2"
USE MTS LOGO ARTWORK
14.0 POINT SIZE
69.85 [2.75]
7.5 POINT SIZE
Level Plus Transmitter
FM14ATEX0068X
IECEx FMG 14.0032X
"L1"
∆ "L2"
INSTALL PER DRAWING # 651543-3
USE MTS LOGO ARTWORK
14.0 POINT SIZE
DESCRIPTION
86.30 [3.40]
7.5 POINT SIZE
UNLESS OTHERWISE SPECIFIED
Level Plus Transmitter
0 PLACES
FM14ATEX0068X
IECEx FMG 14.0032X
NOTES:
MM
0.5
1. STANDARD LETTERING
OR ITC GARAMOND BO
- THREAD DEPTHS ARE TO MIN. FULL THDS
INSTALL PER DRAWING # 651544-3
- DRILL DEPTHS ARE TO FULL DIA.
2. DIMENSIONS IN BRACK
ADDED "D1"
- REMOVE BURRS AND SHARP EDGES
IN INCHES.
- DO NOT SCALE PRINT
P I
R
A
T
N I
G
- MACHINED SURFACE FINISH 3.2uM [125 uIn]
3. MATERIAL: 3M 7883 ME
RELEASE FOR PRODUCTION
4.0 POINT TEXT SIZE
POLYESTER FOIL W/GA
D
E
S
C
R
P I
(TYP.)
INK.
UNLESS OTHERWISE SPECIFIED
TOLERANCES
1 PLACE
0 PLACES
MM
MM
0.5
0.1
- THREAD DEPTHS ARE TO MIN. FULL THDS
- DRILL DEPTHS ARE TO FULL DIA.
R3.30
1.78 [.07
1725
1
DASH #
-1
1.78 [.07
-2
P/N 551629-3 Rev B
17.53 [.69
1725
DASH #
SUPPLY VOLTAGE: 28 VDC
P/N 551703-X Rev C
SEE TAB
4.0 POINT TEXT SIZE
(TYP.)
TOLERANCES
1 PLACE
17.53 [.6
ANGLES
1725
MM
0.1
SUPPLY VOLTAGE: 28 VDC
P/N 551705-X Rev C
W
A
S
6
6
SEE TAB
I T
O
N
TITLE
(ACP) L
ANGLES
m
FIRST
ANGLE
28
15
H
34
LIM
-1
-2
"D1"
F
A
"D1"
P
S
NJ
S
NJ
Publicité
Table des Matières
