Using The Charger For The First Time; Starting The Charge / Discharge Process; Nickel-Cadmium (Ni-Cd) Charge Programs - GRAUPNER 6442 Instructions D'utilisation

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

When the INC and DEC buttons are pressed simultaneously and the ULTRAMAT 17 is initially
connected to a 12 V DC car battery or power supply or a 100~240V AC mains socket, the unit goes
to the language select menu, otherwise it runs through the information routine which provides you
with a brief summary of the essential user settings. The charger's screen displays the following
information.
INC
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
LANGUAGE SELECT
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
ENGLISH
ENTER
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
G r a u p n e r
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
U L T R A M A T
3 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Safety timer
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
on
3 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
buzzer
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
on

10. Starting the charge / discharge process

3 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N i C d
a u t o m a t i c
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
C : 2 . 5 A
l i m i t e d
START
2 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
B A T T E R Y
C H E C K
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
W A I T
P L E A S E . . .
2 sec.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
A U T O
2 3 : 4 0
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
N C + 2 . 5 0 A
1 4 , 7 1 7 V
NiCd
MODE
AUTOMATIC-
program
A set of convenient charge programs for recharging Nickel-Cadmium batteries, as commonly
used for modelling purposes. When the charge / discharge program is finished, the screen
displays the name of the charge program alternating with the message „END", together with the
charge time, the last (dis-) charge current, the charged-in (discharged) capacity and the battery
voltage, and continues to do so until you disconnect the battery. This information can often give
you a useful indication about the Ni-Cd pack's charge characteristics and capacity, or warn you
if the charger has incorrectly assessed the pack as being „full".

9. Using the charger for the first time

DEC
Press and hold the INC and DEC buttons simultaneously,
then switch on the charger to get the language selection
display. Select your language using the INC or DEC button
and confirm with pressing the ENTER button.
The ULTRAMAT 17's name appears on the screen.
After 3 sec. the adjustment of the safety timer (on or off) is
1 7
displayed. For about 3 sec. the safety timer can be switched
on or off by pushing the INC or DEC button.
The safety timer is always switched of for discharging and for
Pb manual charge.
For all other charging programs, the safety timer will be 180min,
if it's switched on.
After another 3 sec. the adustment of the buzzer (on or
off) can be changed by pushing the INC or DEC button.
After another 3 sec. the charger is now ready for use, see
10..
For charging / discharging, or conditioning a pack, select
the desired program as described below, and then set
suitable values.
Hold the START button pressed in for about two seconds,
and the charger will measure and assess the battery.
You can interrupt the charge process at any time with another
short press on the START button.
Note: if you interrupt the charge process by pressing
0 0 8 6 3
the START button, all display parameters are
irretrievably erased.
11. Ni-Cd programs
NiCd
MODE
MANUAL-
program
NiCd
NiCd
MODE
balance
discharge
program
program
NiCd
MODE
MODE
∆ ∆ ∆ ∆ ∆
delta-peak
trigger voltage
23

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Ultramat 17

Table des Matières