Flymo EasiGlide Plus 330V Mode D'emploi page 6

To start the mower [ Fig. O6 / O7 ]:
DANGER! Risk of injury!
Risk of injury if the product does not stop when you
release the start levers.
v Do not bypass the safety devices or switches. For example do
not attach the start levers to the handle.
To start:
The product is provided with a two-handed safety device (start
lever (18) and safety lock-off button
being turned on by accident.
There are two start levers (18)
1. Push the safety lock-off button
lever (18) with the other hand.
The mower starts.
2. Release the safety lock-off button
To prevent a ring being cut in the lawn and to clear any residual grass,
tilt the mower slightly. When the lawnmower has reached full speed gently
lower it onto the lawn.
To stop:
(18)
v Release the start lever .
The mower stops.
To empty the grass box [ Fig. O8 / O9 ]:
DANGER! Risk of physical injury!
Cut injury when the blade turns or the product starts
accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you put /remove the grass box.
Models with a transparent window
(3)
the grass box . This should be cleaned after every lawn mowing.
1. Remove the grass box (3)
This will open the grass box lid
2. Empty the grass box (3) .
3. Replace the grass box (3) . Make sure that it locates securely onto the
deck fixing locations.
4. Close the lid.
(3)
Failure to fit the grass box
poor collection of grass clippings.
Tips to use the mower [ Fig. O10 / O11 ]:
Mow twice a week during the growing season.
The lawn will suffer if more than a third of its length is cut at one time and
this may also result in poor collection.
For the best results mow the outside edge of the lawn in a clockwise
direction first.
Start to mow the edge of the lawn nearest to the power point.
So the cable is laid out on the lawn you have already cut.
For best grass collection always mow in a straight line. Do not swing
the lawnmower from side to side.
For the best cutting results mow in straight lines with an overlap of
approximately 8 – 10 cm on each pass with the mower.
Do not overload the mower. To mow long thick grass may cause the
motor speed to drop and you will hear a change in the motor sound.
If the motor speed drops you may overload the mower which may cause
damage. When you mow in long thick grass a first cut with the cutting
height set higher will help reduce the load.
See To adjust the cutting height.
4. MAINTENANCE
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you maintain the product.
To clean the mower:
DANGER! Risk of injury!
Risk of injury and risk of damage to the product.
6
EGP300VEU-20.960.01.indd 6
(5) ) to prevent the product from
fitted. Either one has to be used to start.
(5) with one hand and pull the start
(5) .
(23) in the lid show the filling level of
by the grass box handle (2) .
(21)
.
(21)
and grass box lid correctly can cause
v Do not clean the product with water or with a water jet
(in particular high-pressure water jet).
v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
To clean the underside of the mower [ Fig. M1 ]:
The underside is easiest to clean after you mowed.
1. Lay the mower on its side carefully.
2. Clean the underside (19) by removing any grass build up with the
(17)
spanner / scraper tool .
3. Clean the blade (14) and the fan (15)
sharp objects).
To clean the outside of the mower [ Fig. M2 ]:
1. Clean the outside with a dry cloth.
(20)
2. Clean the airflow slots with a soft brush (do not use sharp objects).
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Disconnect the product from the mains.
2. Clean the mower (see 4. MAINTENANCE).
3. Store the mower in a dry, enclosed and frost-free place.
Storage positions [ Fig. S1 / S2 ]:
1. Push the lower handle (1) inwards from both sides simultaneously and
fold it forward.
2. Tilt the mower backwards to stand in the vertical storage position.
(11)
3. Wrap the mains cable securely around the mains cable hooks
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household
waste. It must be disposed of in line with local environmental
regulations.
IMPORTANT!
v Dispose of the product through or via your municipal recycling collection
centre.
6. TROUBLESHOOTING
DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the blade to stop, disconnect the product from the
mains and use gloves before you troubleshoot the product.
To replace the blade:
DANGER! Risk of injury!
Cut injury when the blade turns and it is damaged, bent,
out of balance or has chipped edges.
v Do not use the mower when the blade is damaged, bent,
out of balance or has chipped edges.
v Do not regrind the blade.
The FLYMO spare parts are available from your FLYMO dealer or from the
FLYMO service.
Only use an original FLYMO blade:
FLYMO Replacement Blade for 33 cm:
Reference no. FLY095
FLYMO Replacement Blade for 36 cm:
Reference no. FLY096
v Replace the blade (see 3. OPERATION To adjust the cutting height).
Problem Possible Cause
Mower does not start Mains cable is disconnected
or damaged.
Motor is blocked.
with a soft brush (do not use
(H)
.
Part no. 529370790
Part no. 529370890
Remedy
v Connect the mains cable or
if necessary replace it.
v Remove the obstacle.
23.10.20 09:26