Dyson v6 fluffy Manuel D'utilisation page 33

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 35
EN
USING YOUR DYSON APPLIANCE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN THIS DYSON
OPERATING MANUAL BEFORE PROCEEDING.
OPERATION
Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
Ensure the appliance remains upright in use and in storage. Dirt and debris may
be released if it is turned upside down.
Do not operate while checking for blockages.
For domestic indoor and car use only. Do not use it whilst the car is in motion or
while driving.
To operate the Max mode, hold the trigger down and press the 'Max' button.
The 'Max' button will light up.
To switch off Max mode, hold the trigger down and press the 'Max' button
again. Note: The appliance will retain the last used mode. So if you use it in max
mode and do not disengage it, the appliance will operate in Max mode when it
is next used until you depress the 'Max' button to disengage it.
This appliance has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
DOCKING STATION INSTALLATION
Use appropriate mounting hardware for your wall type and ensure that the
docking station is mounted securely. Ensure no pipe work (gas, water, air) or
electrical cables, wires or ductwork are located directly behind the mounting
area. The docking station must be mounted in accordance with regulations
and applicable codes/standards (state and local laws may apply). Dyson
recommends the use of protective clothing, eyeware and materials when
installing the docking station.
CARPETS OR HARD FLOORS
Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
The brush bar on the appliance can damage certain carpet types and floors.
Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this
happens, we recommend vacuuming without the motorised floor tool and
consulting with your flooring manufacturer.
Before vacuuming highly polished floors, such as wood or lino, first check that
the underside of the floor tool and its brushes are free from foreign objects that
could cause marking.
LOOKING AFTER YOUR DYSON APPLIANCE
Do not carry out any maintenance or repair work other than that shown in this
Dyson Operating Manual, or advised by the Dyson Helpline.
Only use parts recommended by Dyson. If you do not this could invalidate
your guarantee.
Store the appliance indoors. Do not use or store it below 3°C (37.4°F).
Ensure the appliance is at room temperature before operating.
Clean the appliance only with a dry cloth. Do not use any lubricants,
cleaning agents, polishes or air fresheners on any part of the appliance.
VACUUMING
Do not use without the clear bin and filter in place.
Fine dirt such as flour should only be vacuumed in very small amounts.
Do not use the appliance to pick up sharp hard objects, small toys, pins,
paper clips, etc. They may damage the appliance.
When vacuuming, certain carpets may generate small static charges in the
clear bin or wand. These are harmless and are not associated with the mains
electricity supply. To minimise any effect from this, do not put your hand or insert
any object into the clear bin unless you have first emptied it. Clean the clear bin
with a damp cloth only. (See 'Cleaning the clear bin'.)
Use extra care when cleaning on stairs.
Do not rest the appliance on chairs, tables, etc.
Do not press down on the nozzle with excessive force when using the appliance
as this may cause damage.
Do not leave the cleaner head in one place on delicate floors.
On waxed floors the movement of the cleaner head may create an uneven lustre. If
this happens, wipe with a damp cloth, polish the area with wax, and wait for it to dry.
DIAGNOSTICS – MAIN BODY
When in use, trigger pressed:
Solid blue: Max 'ON'.
Light off: Powerful suction.
Flashing blue: Low battery warning.
Fast flashing blue: No power, temporary fault
(e.g. check filter or for blockages).
EMPTYING THE CLEAR BIN
Empty as soon as the dirt reaches the level of the MA mark – do not overfill.
Ensure the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
To make emptying the clear bin easier, it is advisable to remove the wand
and floor tool.
To release the dirt, push the red button by the clear bin: Press once to open the
bin base. Press a second time to release the clear bin from the main body of
the appliance.
To minimise dust/allergen contact when emptying, encase the clear bin tightly in
a plastic bag and empty.
Remove the clear bin carefully from the bag.
Seal the bag tightly, dispose as normal.
Close the clear bin base so it clicks into place and is secure.
CLEANING THE CLEAR BIN
Ensure the appliance is disconnected from the charger before removing the
clear bin. Be careful not to pull the 'ON' trigger.
Remove the wand and floor tool.
Push the red button by the clear bin: Press once to open the bin base. Press a
second time to release the clear bin from the main body of the appliance.
Remove the clear bin carefully.
Clean the clear bin with a damp cloth only.
Do not use detergents, polishes or air fresheners to clean the clear bin.
Do not put the clear bin in a dishwasher.
Clean the cyclone shroud with the brush on the combination tool to remove lint
and dust.
Ensure the clear bin is completely dry before replacing.
To replace the clear bin, push the clear bin up and in to the main body of the
appliance. It will click into place.
Close the clear bin base so it clicks into place and is secure.
WASHABLE PARTS
Your appliance has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE BRUSH BARS
Your appliance has two washable brush bars, check and wash these regularly
according to the following instructions to maintain performance.
Ensure the appliance is disconnected from the charger before removing the
brush bar. Be careful not to pull the 'ON' trigger.
TO REMOVE, WASH AND REPLACE BRUSH BARS:
Please refer to the 'Washing the brush bars' illustrations alongside the
instructions below.
Turn the cleaner head upside down so the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter anti-clockwise to the
unlocked position.
Rotate the end cap to the open position. Gently slide the large brush bar away
from the cleaner head.
Remove the end cap from the large brush bar.
Lift out the small brush bar from the octagonal end and pull away from the
cleaner head.
Hold the brush bars under running water and gently rub to remove any lint
or dirt.
Stand both brush bars upright. Ensure the large brush bar is stood upright as
shown. Leave to dry completely for a minimum of 24 hours.
Before replacing, check that the brush bars are completely dry. Refit the small
brush bar before the large one. Insert the round end of the small brush bar into
place. Push down the octagonal end until it clicks into place.
Reattach the end cap to the brush bar.
Slide the large brush bar back onto the cleaner head, around the motor.
The end cap should be in the open position as shown. Once in place, rotate the
end cap back into the closed position.
Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is
fully turned and the base plate and the brush bars are secure.
WASHING THE FILTERS
Your appliance has two washable filters; wash the filters at least once a month
according to the following instructions to maintain performance. More frequent
washing may be required where the user: vacuums fine dust, operates mainly in
'Powerful suction' mode, or uses the machine intensively.
WASHING FILTER A
Ensure the appliance is disconnected from the charger before removing the
filter. Be careful not to pull the 'ON' trigger.
Check and wash the filter regularly according to instructions to
maintain performance.
The filter may require more frequent washing if vacuuming fine dust or if used
mainly in 'Powerful suction' mode.
To remove the filter, lift it out of the top of the appliance.
Wash the filter with cold water only. No hot water and no detergents.
Run water over the outside of the filter until the water runs clear.
Squeeze and twist with both hands to make sure the excess water is removed.
Leave the filter to dry completely for a minimum of 24 hours.
Do not put the filter in a dishwasher, washing machine, tumble dryer, oven,
microwave or near a naked flame.
To refit, place the dry filter back into the top of the appliance. Make sure it is
seated properly.
WASHING FILTER B
To remove the filter, twist anti clockwise to the open position and pull away from
the appliance.
Wash the inside of the filter under cold running water, rotating the filter to
ensure all pleats are covered.
Gently tap the filter against the side of the sink several times to remove
any debris.
Repeat this process 4-5 times until the filter is clean.
Place the filter upright, with the Max button facing upwards, and leave to dry
completely for a minimum of 24 hours.
To refit, return the filter to the open position and twist clockwise until it clicks
into place.
33

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

215871-01

Table des Matières