Working Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch PST 750 PE Notice Originale

OBJ_BUCH-1065-007.book Page 17 Wednesday, January 13, 2016 12:32 PM

Working Advice

 Before any work on the machine itself, pull the mains
plug.
 When working small or thin workpieces, always use a
stable support or a saw station (Bosch PLS 300).
Saw with moderate pressure in order to achieve optimal and
precise cutting results.
For long and straight cuts in thick wood (>40 mm), the cut-
ting line can become inaccurate. In this case, using a Bosch
circular saw is recommended to achieve accurate cuts.
Plunge Cutting (see figure H)
 Plunge cuts may only be applied to soft materials, such
as wood, gypsum plaster boards, etc.!
Use only short saw blades for plunge cutting. Plunge cutting is
possible only with the mitre angle set at 0°.
Place the machine with the front edge of the base plate 6 on
to the workpiece without the saw blade 15 touching the work-
piece and switch on. For machines with stroke rate control,
select the maximum stroke rate. Firmly hold the machine
against the workpiece and by tilting the machine, slowly
plunge the saw blade into the workpiece.
When the base plate 6 fully lays on the workpiece, continue
sawing along the desired cutting line.
Coolant/Lubricant
When sawing metal, coolant/lubricant should be applied
alongside cutting line because of the material heating up.

Maintenance and Service

Maintenance and Cleaning

 Before any work on the machine itself, pull the mains
plug.
 For safe and proper working, always keep the machine
and ventilation slots clean.
Clean the saw blade holder regularly. For this, remove the saw
blade from the machine and lightly tap out the machine on a
level surface.
Heavy contamination of the machine can lead to malfunc-
tions. Therefore, do not saw materials that produce a lot of
dust from below or overhead.
 In extreme conditions, always use dust extraction as
far as possible. Blow out ventilation slots frequently
and install a portable residual current device (PRCD).
When working metals, conductive dust can settle in the in-
terior of the power tool. The total insulation of the power
tool can be impaired.
Lubricate the guide roller 14 occasionally with a drop of oil.
Check the guide roller 14 regularly. If worn, it must be re-
placed through an authorised Bosch after-sales service agent.
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
Bosch Power Tools

After-sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0844) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
Republic of South Africa
Customer service
Hotline: (011) 6519600
Gauteng – BSC Service Centre
35 Roper Street, New Centre
Johannesburg
Tel.: (011) 4939375
Fax: (011) 4930126
E-Mail: bsctools@icon.co.za
English | 17
1 609 92A 1ZE | (13.1.16)