Cleaning, Maintenance, Storage, Transport And Ordering Of Spare Parts; Petrol Engine - EINHELL GC-PM 47/2 S HW Mode D'emploi D'origine

Using one hand, lift up the chute fl ap, while grab-
bing onto the basket handle with the other. Hang
in the basket from the top.
7. Cleaning, maintenance, storage,
transport and ordering of spare
parts
Danger!
Never work on or touch any current-conducting
parts of the ignition system while the engine is
running. Pull the spark plug boot from the spark
boot before doing any maintenance or assembly
work. Never carry out any work on the equipment
while the engine is running. Work that is not de-
scribed in these operating instructions, should
only be carried out by authorized workshops.
7.1 Cleaning in the vertical cleaning position
The lawn mower should be cleaned thoroughly
every time after it has been used. This applies in
particular to its underside and the blade mount.
Note: Before tilting the lawn mower into the ver-
tical cleaning position, use a petrol extraction
pump to drain all the fuel out of the fuel tank. Do
not tilt the lawn mower by more than 90 degrees.
Vertical cleaning position (Fig. 13a/13b)
Important! Before moving the mower into the
vertical cleaning position, switch off the engine
and pull out the spark plug connector. Important!
Place the mower only on a fi rm, level surface.
1. Open the star nuts (Item 11).
2. Press the lower push bar apart and swing it
open (Fig.13a).
3. Move the mower into the vertical cleaning po-
sition (Fig.13b).
4. Clean the bottom side of the mower with the
cleaning scraper (Fig.2/Item 14).
Warning!
Sharp blades! Wear gloves during the cleaning
work.
It is easiest to remove dirt and grass immediately
after mowing. Dried grass remnants and dirt may
impair the mowing operation. Check if the grass
ejector chute is free of grass remnants and remo-
ve any if necessary. Never clean the mower using
a high-pressure cleaner. The engine must remain
dry. Do not use aggressive cleaning agents such
as cold cleaners or petroleum ether.
Anl_GC_PM_47-2_52-2_56-2_S_HW_SPK7.indb 26 Anl_GC_PM_47-2_52-2_56-2_S_HW_SPK7.indb 26
GB
Warning!
•
Leave the mower in the vertical cleaning po-
sition only for as long as necessary because
in this position there is a considerable risk of
injury.
•
Never leave the mower unsupervised.
•
Keep children away.
7.2 Maintenance
Please refer to the supplied petrol service
manual for information on the maintenance
intervals.
Note: Dispose of soiled maintenance material
and operating materials at the appropriate collec-
tion point.

7.2.1 Petrol engine

Note! Never run the engine with no or too little oil.
This can cause serious damage to the engine.
Checking the oil level
Place the lawn mower so that it stands level. Un-
screw the oil dipstick (Fig. 9a/Item 7a) by turning
it counter-clockwise and wipe the dipstick. Re-
insert the dipstick into the fi ller opening as far as it
will go but do not screw it in. Pull out the dipstick,
hold it horizontally and read off the oil level. The
oil level must be between the two marks min. and
max. on the oil dipstick (Fig. 9b).
Changing the oil
The engine oil is best changed when the engine
has been switched off but is still warm.
1. Make sure that the debris bag has been re-
moved.
2. Empty the petrol tank with a petrol suction
pump and run the engine until the remaining
fuel is fully consumed.
3. Place an oil drip tray alongside the mower.
4. Open the oil fi ller plug (Item 7a) and tilt the
mower 90° sideways.
5. The hot oil will fl ow through the open oil fi ller
opening into the oil drip tray.
6. After the old oil has drained out, set the mo-
wer upright again.
7. Fill in engine oil up to the top mark on the oil
dip stick.
8. Dispose of the used oil in accordance with
applicable regulations.
- 26 -
17.09.2019 09:09:10 17.09.2019 09:09:10