Forward Facing Installation - ISOFIX BUN 0123 Guide D'utilisation

4. Pass the abdominal strap of the seat belt through the lower seat
guides (K) (fig.3.3) and buckle the vehicle seat belt until you hear a
click (fig. 3.4).
5. Pass the diagonal section of the seat belt through the corresponding
upper guide (Q) as shown (fig. 3.6).
6. take up the remaining slack of the diagonal section of the 3-point seat
belt (fig. 3.6). and make sure it is as tight fitting as possible. ensure the
straps are not twisted or knotted at any point.
7. Place the seat cushion on the seat.
4. PlaCInG THe CHIld In THe seaT. GRouP 0+/1
Proper adjustment of the height of the harness ensures the child will be
seated correctly. the harness should be adjusted to the height of the
child's shoulder or slightly above; never behind the child's back or level
with the ears (fig. 4.1).
1. loosen the harness straps
the harness adjustment button
(F)
2. release the buckle to make it easier to seat the child (fig. 4.3).
3. Place the child in the seat.
4. secure the child in the harness by joining the two parts of the clasp
and fastening the buckle
5. gently pull the harness adjustment strap to achieve the correct
(G)
tension (fig. 4.5). remember that in order to ensure the child's
safety the harnesses should fit tightly.
5. adJusTInG THe HeadResT HeIGHT
Proper adjustment of the height of the headrest ensures the child will
be seated correctly. the headrest should be adjusted to ensure that
(E)
the harness straps should be adjusted to the height of the child's
shoulder or slightly above; never behind the child's back or level with
the ears (fig. 4.1).
1. loosen the harness straps
harness adjustment button
22
(E)
by pulling them gently while pressing
(J)
(fig. 4.2).
(F)
until you hear a click (fig. 4.4).
(E) by pulling them gently while pressing the
(J) (fig. 5.1).
2. adjust the headrest according to the child´s height by pulling the headrest
height regulator
shoulder or slightly above (fig. 5.2).
6. InsTallInG THe CaR seaT FoRWaRd FaCInG. GRouP 1
For group 1 this car seat has 2 modes of installation. although we advise
to use the seat backward facing to the travel direction for an up to 15
months child, it is possible to install the seat forward facing, if:
• The size of the vehicle does not allow safe installation of the seat
backward facing.
• The size of the child exceeds the height percentiles and this causes
the child to be incorrectly positioned in the seat.

6.1 Forward facing installation

1. ensure the seat is not in a reclined position (the indicator should be
in position 1) and is ready to install in forward position (group 1) as
shown fig. 6.1. Pull the lever
to position 4 without releasing the lever. release the lever when the seat
is in the desired position (fig. 6.1)
2. Pull the isoFiX adjuster
arms from side to side until you hear the click indicating that they are
fully locked (fig. 6.2).
3. take the top tether and pass it over the seat.
4. Place the child safety seat in the back seat of the vehicle facing in the
direction of travel.
5. hold the safety seat with both hands and insert the two locking arms
into the verhicle´s isofix connectors until they fasten with a click on both
sides. the red button will change to green on both sides (fig. 6.3).
6. shake the seat to check that it is correctly anchored to the vehicle's
isoFiX points.
IMPoRTanT! the locking arms are only correctly fixed if both safety
buttons are green.
BUN 0123
(A) adjusting the harness to the height of the child´s
GRouP 1 only. From 9 months to 4 years
noTICe
approx. (9-18 kg)
(H)
forward and adjust the angle of recline
(I) to extract both arms (M). move the locking
(M)
www.babyqs.com
23