Bosch GBH 18V-34 CF Professional Notice Originale page 10

10 | English
Make sure that the retaining strap of the auxiliary handle
slots into the corresponding groove of the housing.
Setting the drilling depth (see figure B)
You can use the depth stop (17) to set the required drilling
depth X.
– Press the button for depth stop adjustment (15) and in-
sert the depth stop into the auxiliary handle (16).
The fluting on the depth stop (17) must face downwards.
– Push the SDS plus application tool into the SDS plus tool
holder (3) as far as it will go. Otherwise, the movability of
the SDS-plus drilling tool can lead to incorrect adjustment
of the drilling depth.
– Pull the depth stop far enough out that the distance
between the drill bit tip and the edge of the depth stop
corresponds to the required drilling depth X.
Selecting drill chucks and tools
For hammer drilling and chiselling, you will need SDS plus
tools, which insert into the SDS plus drill chuck.
For drilling without impact in wood, metal, ceramic and
plastic as well as for screwdriving, tools without SDS plus
are used (e.g. cylindrical shank drill bits). For these tools,
you will need the keyless quick-change chuck (1) with integ-
rated impact stop.
Note: Using the keyless quick-change chuck (1) with integ-
rated impact stop is the only way to ensure that the tools in-
serted are not damaged.
Removing/inserting the quick-change chuck
Removing the Quick-Change Chuck (see figure C)
– Pull back on the quick-change chuck locking ring (6), hold
it in this position and pull the SDS plus quick-change
chuck (2) or the keyless quick-change chuck (1) out from
the front.
– Once the quick-change chuck is removed, protect it from
dirt.
Inserting the Quick-Change Chuck (see figure D)
– Before insertion, clean the quick-change chuck and lightly
grease the shank.
– Wrap your whole hand around the SDS plus quick-change
chuck (2) or the keyless quick-change chuck (1). Use a
turning motion to push the quick-change chuck into the
drill chuck holder (20) until you hear it click into place.
– The quick-change chuck is automatically locked. Check
that it is locked by pulling on the quick-change chuck.
Changing the Tool
The dust protection cap (4) largely prevents the penetration
of drilling dust into the tool holder during operation. When
inserting the tool, make sure that the dust protection cap (4)
does not become damaged.
Replace a damaged dust protection cap immediately.
u
It is recommended that you have use an after-sales
service for this.
1 609 92A 5JT | (13.10.2020)
Changing the tool (SDS plus)
Inserting the SDS plus application tool (see figure E)
The SDS-plus drill chuck enables you to change the applica-
tion tool easily and conveniently without needing to use ad-
ditional tools.
– Insert the SDS plus quick-change chuck (2).
– Clean and lightly grease the shank of the application tool.
– Insert the application tool into the tool holder while turn-
ing it until it locks automatically.
– Check that it is locked by pulling on the tool.
As a requirement of the system, the SDS-plus application
tool can move freely. This causes a certain radial run-out at
no-load, which has no effect on the accuracy of the drill hole,
as the drill bit centres itself upon drilling.
Removing SDS-plus application tools (see figure F)
– Push the locking sleeve (5) back and remove the applica-
tion tool.
Changing the tool (without SDS plus)
Inserting the Application Tool (see figure G)
Note: Application tools that do not have SDS plus must not
be used for hammer drilling or chiselling. Tools without SDS
plus and their drill chucks are damaged by hammer drilling
or chiselling.
– Insert the keyless quick-change chuck (1) with integrated
impact stop.
Note: Only use the keyless quick-change chuck with integ-
rated impact stop specifically designed for the
GBH 18V-34 CF. Using this drill chuck is the only way to en-
sure that the pneumatic impact mechanism of the rotary
hammer does not damage the application tools.
– Hold the retaining ring (22) of the keyless quick-change
chuck firmly in place. Open the tool holder by turning the
front sleeve (21) until the tool can be inserted. Hold the
retaining ring (22) in place and firmly tighten the front
sleeve (21) by turning it in the direction of the arrow until
you hear it click into place.
– Check that it is seated securely by pulling on the tool.
Note: If the tool holder was unscrewed all the way, a scrap-
ing sound may be heard while retightening the tool holder
and it may not fully tighten.
In this case, turn the front sleeve (21) in the opposite direc-
tion to the arrow by one full turn. This will allow the tool
holder to be fully tightened.
– Turn the combi switch (7) to the "drilling" position.
Removing the application tool (see figure H)
– Hold the retaining ring (22) of the keyless quick-change
chuck firmly in place. Open the tool holder by turning the
front sleeve (21) in the direction of the arrow until the
tool can be removed.
Dust/Chip Extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Bosch Power Tools