Bosch GKS 10,8 V-LI Professional Notice Originale page 17

Masquer les pouces Voir aussi pour GKS 10,8 V-LI Professional:
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 21
OBJ_BUCH-2006-002.book Page 17 Tuesday, February 10, 2015 10:13 AM
32 Parallel guide/guide rail adapter*
33 Set of screw clamps*
34 Guide rail*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Circular Saw
Article number
Rated voltage
No-load speed
Cutting depth, max.
– for 0° bevel angle
– for 45° bevel angle
Spindle lock
Base plate dimensions
Saw blade diameter, max.
Saw blade diameter, min.
Blade thickness, max.
Tooth thickness/setting, max.
Tooth thickness/setting, min.
Mounting bore
Weight according to
EPTA-Procedure 01/2003
Permitted ambient temperature
– during charging
*
– during operation
and during
storage
Recommended batteries
Recommended chargers
* Limited performance at temperatures <0 °C
Noise/Vibration Information
Sound emission values determined according to
EN 60745-2-5.
Typically the A-weighted noise levels of the product are:
Sound pressure level 90 dB(A); Sound power level
101 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
Vibration total values a
(triax vector sum) and uncertainty K
h
determined according to EN 60745-2-5:
2
Cutting wood: a
=2.5 m/s
, K=1.5 m/s
h
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
Bosch Power Tools
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
GKS 10,8 V-LI
Declaration of Conformity
3 601 FA1 0..
V=
10.8
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
-1
min
1400
vant provisions of the directives 2009/125/EC (Regulation
1194/2012), 2011/65/EU, until 19 April 2016:
mm
26.5
2004/108/EC, from 20 April 2016 on: 2014/30/EU,
mm
17.0
2006/42/EC including their amendments and complies with
the following standards: EN 60745-1, EN 60745-2-5.
mm
167 x 88
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
mm
85
70764 Leinfelden-Echterdingen, GERMANY
mm
85
Henk Becker
mm
0.7
Executive Vice President
mm
1.1
Engineering
mm
1.0
mm
15
kg
1.4
Robert Bosch GmbH, Power Tools Division
70764 Leinfelden-Echterdingen, GERMANY
Leinfelden, 10.02.2015
°C
0...+45
Assembly
°C
–20...+50
GBA 10,8V ...
Battery Charging
AL 11..
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium-ion battery of your power tool.
Note: The battery supplied is partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The lithium-ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging procedure
does not damage the battery.
The lithium-ion battery is protected against deep discharging
by the "Electronic Cell Protection (ECP)". When the battery is
empty, the machine is switched off by means of a protective
2
.
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
Observe the notes for disposal.
Removing the battery
The battery 1 is equipped with two locking levels that should
prevent the battery from falling out when pushing the battery
unlocking button 2 unintentionally. As long as the battery is
inserted in the power tool, it is held in position by means of a
spring.
English | 17
Helmut Heinzelmann
Head of Product Certification
PT/ETM9
1 609 92A 14P | (10.2.15)

Publicité

Table des Matières
loading

Table des Matières