Bosch GTS 10 XC Professional Notice Originale page 39

OBJ_BUCH-1375-002.book Page 39 Monday, August 29, 2011 5:05 PM
– Turn the saw blade until the marked tooth projects above
the right side of the insert plate.
– Move the angle gauge alongside the guide groove to the
marked tooth.
– Measure the clearance between the saw blade and guide
groove again.
Both clearances measured must be identical.
Adjusting:
– Loosen Allen screws 70 at the front below the saw table
and Allen screws 71 at the rear below the saw table with
the supplied Allen key 37.
– Carefully move the saw blade until it is parallel to guide
groove 9.
– Retighten all screws 70 and 71 again.
Adjusting the Saw Table's Clearance Indicator
(see figure O)
– Position the parallel guide on the right side of the saw
blade.
Move the parallel guide until the mark in the lens 64 indi-
cates 33 cm on the bottom scale.
To lock the parallel guide, press clamping handle 47 down
again.
– Completely pull clamping handle 18 upward and pull the
table width enlargement 11 outward to the stop.
Checking:
On the upper scale 1, clearance indicator 65 must indicate
the identical value as the mark in lens 64 on the bottom scale
1.
Adjusting:
– Loosen screw 72 with a Phillips screwdriver and align
clearance indicator 65 alongside the 33 cm mark of the up-
per scale 1.
Adjusting the Lens of the Parallel Guide (see figure P)
– Bring the power tool into the working position.
– Tilt the blade guard 5.x toward the rear to the stop.
– Move parallel guide 8 from the right until it touches the saw
blade.
Checking:
The mark of lens 64 must be in a line with the 0° mark of scale
1.
Adjusting:
– Loosen screw 73 using a Phillips screwdriver and align the
clearance indicator alongside the 0° mark.
Adjusting the Level of the Insert Plate (see figure Q)
Checking:
The front side of the insert plate 31 must be flush with or
somewhat lower than the saw table; the rear side must be
flush with or somewhat above the saw table.
Adjusting:
– Adjust the correct level of the four adjusting screws 74
with a suitable slotted screwdriver.
Bosch Power Tools
Adjusting the Tension Force of the Parallel Guide
The tensioning force of the parallel guide 8 can decrease after
frequent usage.
– Tighten the adjustment screw 81 until the parallel guide
can be firmly affixed on the saw table again.
Storage and Transport
Storing Product Features (see figures R1–R6)
For storage purposes, certain product features can be se-
curely fastened to the power tool.
– Loosen auxiliary parallel guide 49 from parallel guide 8.
– Attach all loose tool parts to their storage locations on the
housing. (see Table)
Figure Product Feature Storage Location
R1 Blade guard 5.x Insert into the recess of fixture
22 and tighten with clamping
lever 46.1 or clamping screw
46.2
R2 "Auxiliary parallel Clip into the holders 75
guide" fastening
kit 39
R2 Extraction Insert into retaining clamp 76
adapter 41
R3 Unused saw Insert into saw blade storage 77
blades and lock the cover 14 over it
with fastening nut 12
R3 Ring spanner 15 Insert into saw blade storage 77
and lock the cover 14 over it
with fastening nut 12
R3 Push stick 13 Lock in place with fastening nut
12
R4 Allen key 37 Insert into holders 78
R4 Parallel guide 8 Insert into the storage compart-
ment for the parallel guide 36
R5 Angle stop 3 Insert into retaining clamp 23
R6 Auxiliary parallel Insert into the storage compart-
guide 49 ment for the auxiliary parallel
guide and lock in place with the
retaining bracket 79
Carrying the Power Tool
Before transporting the power tool, the following steps must
be carried out:
– Bring the machine into the transport position.
(see "Transport Position", page 36)
– Remove all accessories that cannot be mounted firmly to
the power tool.
If possible, place unused saw blades in an enclosed con-
tainer for transport.
– Slide the table width enlargement 11 completely in and
press tensioning lever 18 downward to lock it.
– Slide the table extension 10 completely in and firmly tight-
en the locking screws 38 on the guide rods 24.
– Wind the mains cable around the cable holder 42.
– For lifting or transport, use the carrying handles 4.
English | 39
1 619 929 K16 | (29.8.11)