Kenwood KDC-X396 Mode D'emploi page 15

Item
EQ PRO (for
BASS ADJUST BASS CTR FRQ
BASS LEVEL
BASS Q FACTOR 1.00 */ 1.25/ 1.50/ 2.00: Adjusts the quality factor.
BASS EXTEND
MID ADJUST MID CTR FRQ
MID LEVEL
MID Q FACTOR
TRE ADJUST TRE CTR FRQ
TRE LEVEL
PRESET EQ NATURAL */ USER/ ROCK/ POPS/ EASY/ TOP40/ JAZZ/ POWERFUL: Selects a preset sound mode
suitable to the music genre. (Selects [USER] to use the customized bass, middle, and treble settings.)
BASS BOOST B.BOOST LV1/ B.BOOST LV2/ B.BOOST LV3: Selects your preferred bass boost level. ; OFF *: Cancels.
LOUDNESS LOUDNESS LV1 */ LOUD LV1 */ LOUDNESS LV2/ LOUD LV2: Selects your preferred low and high
frequencies boost to produce a well-balanced sound at a low volume level. ; OFF: Cancels.
BALANCE L15 — R15 (Preset: 0): Adjusts the left and right speaker output balance.
FADER R15 — F15 (Preset: 0): Adjusts the rear and front speaker output balance.
SUBWOOFER SET/ ON *: Turns on the subwoofer output. ; OFF: Cancels.
SUB-W SET
DETAILED SET/ DETAIL SET
HPF
For
120HZ/ 150HZ: Frequencies lower than the specified value are cut off.
LPF SUBWOOFER/ THROUGH *: All signals are sent to the subwoofer. ; 85HZ/ 120HZ/ 160HZ: Frequencies higher than
LPF SUB-W 85 Hz/ 120 Hz/ 160 Hz are cut off.
SUB-W PHASE REVERSE/ REV (180°)/ NORMAL/ NORM (0°) *: Selects the phase angle of the subwoofer output to
be in line with the speaker output for optimum performance. (Selectable only if a setting other than
[THROUGH] is selected for [LPF SUBWOOFER] / [LPF SUB-W].)
SUPREME SET ON *: Creates realistic sound by interpolating the high-frequency components that are lost in MP3/
WMA audio compression. ; OFF: Cancels. (Selectable only when playback an MP3/WMA disc or a USB
device, except iPod.)
VOLUME OFFSET/ –8 — +8 (for AUX) ; –8 — 0 (for other sources): Presets the volume adjustment level of each
VOL OFFSET source. The volume level will automatically increase or decrease when you change the source. (Before
(Preset: 0) making an adjustment, select the source you want to adjust.)
For
[SUB-W LEVEL/ SUB-W SET/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SWITCH PRE] is set to [SUB-W]. (page 8)
[SUB-W LEVEL/ LPF SUB-W/ SUB-W PHASE] is selectable only if [SUB-W SET] is set to [ON].
Selectable setting (Preset: *)
)
60/ 80/ 100 */ 200: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.
ON: Turns on the extended bass. ; OFF *: Cancels.
0.5K/ 1.0K */ 1.5K/ 2.5K: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.
0.75/ 1.00 */ 1.25: Adjusts the quality factor.
10.0K/ 12.5K */ 15.0K/ 17.5K: Selects the center frequency.
–8 — +8 (Preset: 0): Adjusts the level.
: THROUGH *: All signals are sent to the speaker. ; 100HZ/
:
Continued...
15