Invacare P409 Asteria Manuel D'utilisation page 4

Invacare® P409 Asteria
1. Press the snap button A.
2. Slide the extension up or down until the desired height
is achieved.
3. Allow the snap button A to click into the next hole.
Make sure that the button is fully engaged with an
audible "click".
4.4 Walking
1. Stand between the two side frames and hold both hands
on the handles.
2. Stand still and move/slide the walking aid forwards.
3. Take a step forwards while holding the walking aid
steady.
4.5 Using leg extensions
WARNING!
Risk of falling
– When using wheeled attachments on the front
legs, the rear leg extensions must be adjusted
to make the side frames level.
– When applicable, wheeled leg extensions must
be installed with the wheels on the outside of
the walkerwalking frame.
See section "Adjusting the height" for more
information.
5 Maintenance
5.1 General Maintenance Information
WARNING!
Risk of Injury
– Maintenance should be done at least once a
year.
– Do not use a defective product.
– Do not attempt repairs yourself. For repairs
contact your provider.
5.2 Inspection Checklist
To ensure good performance and safety, inspect your product
regularly.
q
Ensure that all screws and adjustments are properly
tightened. (If applicable)
q Ensure that hand grips are tight.
If hand grips are loose do not use the walking aid.
Instructions on how to change hand grips can be
obtained from your provider or Invacare distributor.
q Inspect the frame and loaded parts for cracks.
q Inspect the wheels' tightness, wear and damage. (If
applicable)
q
Make sure that the wheels are free of hair, lint and
other debris. (If applicable)
q Ensure that the rubber tips and/or plastic glide tips are
not ripped, worn or missing. (If applicable)
5.3 Cleaning and Disinfection
General Safety Information
CAUTION!
Risk of Contamination
– Take precautions for yourself and use
appropriate protective equipment.
4
IMPORTANT!
Wrong fluids or methods can harm or damage
the product.
– All cleaning agents and disinfectants used must
be effective, compatible with one another and
must protect the materials they are used to
clean.
– Never use corrosive fluids (alkalines, acid etc.)
or abrasive cleaning agents. We recommend
an ordinary household cleaning agent such as
dishwashing liquid, if not specified otherwise in
the cleaning instructions.
– Never use a solvent (cellulose thinner, acetone
etc.) that changes the structure of the plastic
or dissolves the attached labels.
– Always make sure that the product is completely
dried before taking it into use again.
For cleaning and disinfection in clinical or long-term
care environments, follow your in-house procedures.
Cleaning Intervals
IMPORTANT!
Regular cleaning and disinfection enhances
smooth operation, increases the service life and
prevents contamination.
Clean and disinfect the product
– regularly while it is in use,
– before and after any service procedure,
– when it has been in contact with any body
fluids,
– before using it for a new user.
Cleaning Instructions
The product can be washed in a washing machine or by hand.
When using a high-pressure cleaner or an ordinary jet of
water, do not aim the jet towards bearings, draining holes
or labels.
The maximum cleaning temperature is 60 °C. Do not use
a steam cleaner.
1. Clean the walking aid with a damp cloth and mild
detergent.
2. Clean the wheels with a brush (no wire brush).
3. After washing, wipe the product dry.
Disinfection
• Wipe down all generally accessible surfaces with
disinfectant.
Information on recommended disinfectants
and methods can be found on https://vah-
online.de/en/for-users.
6 After Use
6.1 Disposal
Be environmentally responsible and recycle this product
through your recycling facility at its end of life.
Disassemble the product and its components, so the different
materials can be separated and recycled individually.
The disposal and recycling of used products and packaging
must comply with the laws and regulations for waste handling
in each country. Contact your local waste management
company for information.
1516319-E