Cleaning The Flue; Majolicas (If Present); Products Made Of Natural Stone (If Present); Varnished Products (If Present) - LA NORDICA ROSA REVERSE Manuel Utilisateur

CLEANINg THE FLUE

The correct lighting phase, the use of proper quantities and types of fuels, the correct position of the secondary air regulator, enough draught
of the chimney-flue and the presence of combustion air are the essential elements for the optimal functioning of the appliance.
THE DEVICE SHOULD BE COMPLETELY CLEANED AT LEAST ONCE A YEAR OR EVERY TIME IT IS NEEDED (in case of bad working and low yield).
AN EXCESSIVE DEPOSIT OF SOOT CAN CAUSE PROBLEMS IN THE DISCHARGE OF SMOKES AND FIRE IN THE FLUE.
THE CLEANINg MUsT BE CARRIED OUT EXCLUsIVELY WITH COLD EQUIPMENT. THIS OPERATION SHOULD BE CARRIED
OUT BY A CHIMNEY SWEEPER WHO CAN SIMULTANEOUSLY PERFORM AN AUDIT OF THE FLUE (checking of possible deposits).
During the cleaning, it is necessary to remove the ash drawer and the smoke deflectors from the device in order to ease the cleaning of the
soot. The deflectors can be easily extracted from their seats since they are not fastened using screws. Once the clearing has been carried out,
place them back in their seats
CAUTION: THE LACk OF THE DEFLECTORs CAUsEs A sTRONg DEPREssION, WITH A TOO FAsT COMBUsTION, AN
EXCEssIVE CONsUMPTION OF WOOD WITH RELATED OVERHEATINg OF THE DEVICE.

MAJOLICAs (IF PREsENT)

La NORDICA s.p.A.has chosen majolica tiles, which are the result of high-quality artisan work. As they are completely carried out by hand,
the majolica may present crackles, speckles, and shadings. These characteristics certify their precious origin.
Enamel and majolica, due to their different coefficient of dilatation, produce microcrackles, which show their authentic feature.
FOR THE CLEANING OF THE MAJOLICA WE SUGGEST YOU TO USE A SOFT AND DRY CLOTH;
IF YOU UsE A DETERgENT OR LIQUID, THE LATTER MIgHT sOAk IN AND HIgHLIgHT THE CRACkLEs PERMANENTLY.

PRODUCTs MADE OF NATURAL sTONE (IF PREsENT)

NATURAL STONE HAS TO BE CLEANED WITH VERY THIN ABRASIVE PAPER OR WITH AN ABRASIVE SPONGE. DO NOT UsE ANY CLEANSER
OR FLUID.

VARNIsHED PRODUCTs (IF PREsENT)

After some years of product use a change in the varnished details colour is totally normal. This is due to the considerable temperature range
the product is subject to whenever in use and to the varnish ageing of time passing by.
ATTENTION: BEFORE ANY POSSIBLE APPLICATION OF THE NEW VARNISH, DO CLEAN AND REMOVE ALL THE TRACES FROM
THE SURFACE WHICH HAS TO BE VARNISHED.

ENAMELLED PRODUCTs (IF PREsENT)

For the cleaning of enamelled surfaces use soap water or NOT AggREssIVE and NOT CHEMICALLY abrasive detergents.
AFTER THE CLEANING DO NOT LET SOAPY WATER OR ANY CLEANSER DRY BUT REMOVE THEM IMMEDIATELY.
DO NOT UsE sANDPAPER OR sTEEL WOOL.

CHROMIUM-COMPONENTs (IF PREsENT)

If the components become bluish due to overheating, this can be solved with a suitable product for cleaning. DO NOT use abrasives or
solvents.

LATERAL HANDRAIL (IF PREsENT)

The handles, the handrail and the tank water (cookers) should be cleaned to cold with a soft cloth and alcohol . DO NOT use abrasives or
solvents.

CLEANINg OF THE HEARTH gRATE

IMPORTANT: if for whatever reason the grill is removed from the furnace, take care to reassemble it with the wider part of the slit facing
Picture 8). This is to aid furnace cleaning.
downwards (See

CAsT IRON COOkINg PLATE AND RINgs

IMPORTANT: TO AVOID RUsT DO NOT FORgET POTS OR PANS ON THE COLD COOKING PLATE. This would create rust rings,
unpleasant to see and difficult to remove.
The cast iron cooking plate and the cast iron rings needs to be periodically cleaned by using sandpaper (grain 150) WITHOUT
TOUCHINg THE ENAMELLED PARTs.
To carry out the cleaning operation remove the smoke outlet spigot and the smoke pipe. The smoke compartment can be cleaned from the
front side of the oven (see chap. CLEANING SMOKE COMPARTMENT COOKERS) or from the top. In this case remove the cast iron rings and the
cooking plate, as well the smoke outlet spigot and the smoke pipe. The cleaning can be carried out by using a brush and a hoover.
ATTENTION: ONCE THE CLEANINg OPERATIONs ARE TERMINATED ALL THE PARTs HAVE TO BE RE-AssEMBLED
HERMETICALLY.
9).
(Picture
ENgLIsH 31