Operation - RIDGID RD80702 Manuel D'utilisation

OPERATION

wARNING:
Do not allow familiarity with this product to make
you careless. Remember that a careless fraction of
a second is sufficient to inflict serious injury.
wARNING:
Always wear eye protection marked to comply with
ANSI Z87.1. Failure to do so could result in objects
being thrown into your eyes, resulting in possible
serious injury.
wARNING:
Do not use any attachments or accessories not recom-
mended by the manufacturer of this product. The use of
attachments or accessories not recommended can
result in serious personal injury.
wARNING:
Never direct a water stream toward people or
pets, or any electrical device. Failure to heed this
warning could result in serious injury.
APPLICATIONS
You may use this product for the purposes listed below:
 Removing dirt and mold from decks, cement patios, and
house siding
 Cleaning cars, boats, motorcycles, outdoor furniture, and
grills
ADDING OIL TO THE ENGINE
See Figure 12.
NOTE: This machine has been shipped with approximately
4 oz. of oil in the engine from testing. You must add oil to
the engine before starting it the first time.
CAUTION:
Any attempt to start the engine without adding oil
will result in engine failure.
 Place pressure washer on a flat, level surface.
 Unscrew the oil cap / dipstick by turning counter-
clockwise.
 Using 4-stroke engine oil (SAE 30 or SAE 10W30), fill to
the upper level of the oil filler neck (12 oz., 4-cycle engine
oil provided).
 Replace the oil cap / dipstick and securely tighten.
NOTE: This engine has a total oil capacity of 20 oz.
(.6 liters).
ADDING GASOLINE TO THE FUEL TANK
See Figure 13.
wARNING:
Gasoline and its vapors are highly flammable and
explosive. To prevent serious personal injury and
property damage, handle gasoline with care. Keep
away from ignition sources, handle outdoors only,
do not smoke while adding fuel, and wipe up spills
immediately.
When adding gas to the pressure washer, make sure the unit
is sitting on a flat, level surface. If the engine is hot, let the
pressure washer cool before adding gas. ALWAYS fill the
fuel tank outdoors with the machine turned off.
NOTE: Use unleaded gas only. DO NOT mix oil with gas.
 Turn the engine switch to OFF ( O ) position.
 Before removing the fuel cap, clean the area around it.
Remove the fuel cap.
 Insert a clean funnel into the fuel tank then slowly
pour gasoline into the tank. Fill tank to approximately
1/2 in. below the top of the tank neck (this allows for fuel
expansion).
 Replace fuel cap and tighten securely.
 Clean up any spills before starting the engine.
OXYGENATED FUELS
Some conventional gasolines are blended with alcohol or an
ether compound. These gasolines are collectively referred
to as oxygenated fuels. To meet clean air standards, some
areas of the United States and Canada use oxygenated fuels
to help reduce emissions.
If using an oxygenated fuel, make sure it is unleaded and
meets the minimum octane rating requirements. Before using
an oxygenated fuel, try to confirm the fuel's contents. Some
states/provinces require this information to be posted on the
pump. The following are the EPA approved percentages of
oxygenates:
Ethanol (ethyl or grain alcohol) 10% by volume. You
may use gasoline containing up to 10% ethanol by volume.
Gasoline containing ethanol may be marketed under the
name "Gasohol." Do not use E85 fuel.
MTBE (methyl tertiary butyl ether) 15% by volume. You
may use gasoline containing up to 15% MTBE by volume.
Methanol (methyl or wood alcohol) 5% by volume. You
may use gasoline containing up to 5% methanol by volume
as long as it also contains cosolvents and corrosion inhibi-
tors to protect the fuel system. Gasoline containing more
than 5% methanol by volume may cause starting and/or
performance problems. It may also damage metal, rubber,
and plastic parts of the product or your fuel system.
If you notice any undesirable operating symptoms, try another
service station or switch to another brand of gasoline.
9 - English