Table des Matières
Publicité
raccordement du câblage Ca (en option)
Le contrôleur SubDrive solaire dispose d'un câblage pour le courant alternatif destiné à une
utilisation avec un générateur lorsque l'alimentation solaire en courant continu n'est pas disponible.
1. Assurez-vous que le générateur est hors tension.
2. Assurez-vous que l'interrupteur externe CC est désactivé.
3. Connectez les câbles du générateur au bornier marqué « Sauvegarde de secours AC », bornes
L1, L2 et GND. (Figure 5) (Spécifi cation de couple : 15 po-lbs (1,7 nm)
L1
raccordement du câblage de l'interrupteur de débit
Le contrôleur SubDrive solaire utilise un interrupteur de débit pour protéger le contrôleur et le moteur
lorsqu'il n'y a pas assez de puissance pour générer le débit adéquat. L'interrupteur de débit et le câble
du capteur sont inclus avec le QuickPAK du SubDrive solaire et sont requis sur toutes les installations.
1. Connectez les câbles depuis les bornes S1 et S2 de l'interrupteur de débit étiquetées « TRIP »
(Figure 7).
aTTenTion
Un défaut d'installation de l'interrupteur de débit inclus aurait pour effet des performances réduites
et pourrait entraîner des dommages au système.
16
COMM.
COMM.
STATUS
MENU
SELECT
UP
DOWN
225979101,3
-
+
RS-485
225996101,2
E1
Display
Status
Run
Idle
Motor
Mode
Mode
Underloaded
Suitable for use on a photovoltaic circuit capable of delivering not more
than 50 DC amps short circuit current, or on a backup AC generator
Service
capable of delivering not more than 5000 amps symmetrical RMS current.
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Diagnostic Aid
COM
Tighten terminals to 7 in-lbs.
Tighten terminals to 7 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
NC
NO
L2
+
+
-
L1
L1
L2
L2
(GND)
(GND)
(GND)
(GND)
(GND)
RUN
SOLAR PRIMARY
SOLAR PRIMARY
SOLAR PRIMARY
BACKUP
BACKUP
BACKUP
BACKUP
DC
DC
DC
AC
BACKUP
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
AC
COMM.
COMM.
STATUS
MENU
SELECT
UP
DOWN
225979101,3
-
+
RS-485
225996101,2
E1
Display
Run
Idle
Motor
Status
Mode
Mode
Underloaded
Suitable for use on a photovoltaic circuit capable of delivering not more
Suitable for use on a photovoltaic circuit capable of delivering not more
Suitable for use on a photovoltaic circuit capable of delivering not more
than 50 DC amps short circuit current, or on a backup AC generator
than 50 DC amps short circuit current, or on a backup AC generator
than 50 DC amps short circuit current, or on a backup AC generator
Service
capable of delivering not more than 5000 amps symmetrical RMS current.
capable of delivering not more than 5000 amps symmetrical RMS current.
capable of delivering not more than 5000 amps symmetrical RMS current.
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
See manual for allowed ratings of solar array (DC) and generator (AC).
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Use 90 °C wire rated 600V min for DC and 300V min for AC.
Diagnostic Aid
COM
Tighten terminals to 7 in-lbs.
Tighten terminals to 7 in-lbs.
Tighten terminals to 15 in-lbs.
Tighten terminals to 15 in-lbs.
NC
NC
NC
+
+
-
L1
L1
L2
L2
(GND)
(GND)
SOLAR PRIMARY
SOLAR PRIMARY
BACKUP
BACKUP
DC
DC
AC
AC
AC
Multiple electrical power sources may be connected.
Multiple electrical power sources may be connected.
Multiple electrical power sources may be connected.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
Disconnect all electrical power before servicing.
TRIP
Error Codes
E2
E3
E4
E5
E6
E7
E8
E9
Figure 6. Raccordement du câblage CA
Under
Locked
External
Open
Short
Overheated
Internal
Voltage
Pump
Trip
Circuit
Circuit
Controller
Reserved
Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
in the Installation/Operation manual intended for use
with this product. Additional copies of the
Installation/Operation manual may be ordered by
contacting your local Franklin Electric representative.
Tighten terminals to 15 in-lbs.
BLK
RED
YEL
STOP
TRIP
(GRY)
(BLK)
(BRN) (GND)
MOTOR
Figure 7. Raccordement du câblage
de l'interrupteur de débit
Error Codes
E2
E3
E4
E5
E6
E7
E8
E9
Under
Locked
External
Open
Short
Internal
Controller
Overheated
Reserved
Voltage
Pump
Trip
Circuit
Circuit
Error
WARNING – Operation of this equipment requires
detailed installation and operation instructions provided
in the Installation/Operation manual intended for use
with this product. Additional copies of the
Installation/Operation manual may be ordered by
contacting your local Franklin Electric representative.
Tighten terminals to 15 in-lbs.
BLK
RED
YEL
(GRY)
(BLK)
(BRN) (GND)
STOP
TRIP
MOTOR
Publicité
Table des Matières
