Mounting Instructions - Hansgrohe AXOR Urquiola 42512180 Instructions De Montage

Mounting instructions
EN
Target group
The basic set may only be mounted by a specialist fitter.
Safety instructions
▸ Read the entire mounting instructions thoroughly before car-
rying out mounting.
Danger of being crushed and danger of injury
at sharp edges!
▸ Wear protective clothing, protective gloves and
safety shoes.
Danger of injury and property damage if the
radiator falls over!
The supplied screws and screw anchors are only suit-
able for concrete.
▸ In case of other floor structures observe the specifi-
cations of the screw anchor manufacturer.
Complaints
We are always ready to assist in solving any problems. However,
you can only assert claims arising from legal right against your
contractual partner from whom you bought the product.
Repairs
Spare parts (→ Fig. D)
Disposal
▸ Recycle packaging or dispose of it properly. Observe the
local regulations.
Technical features
Supply Possible on right or left
Mounting
The radiator can be mounted in the following variants:
• free-standing mounting (mounting examples and dimensions
→ Fig. A)
• wall mounting (dimensions → Fig. B)
A
Free-standing mounting variant (→ Fig. A1–A14)
Danger of injury and property damage if the
radiator falls over!
▸ Mount at least 2 basic sets in order to ensure stability.
▸ Check whether the scope of delivery is complete and free of
damage.
▸ Lay out the required tools.
▸ Mount grommets on the basic sets.
▸ Set up the basic sets and connect with the spacer.
▸ Mark the drill holes.
▸ Drill the holes and insert the screw anchors.
▸ Screw in the hanger bolts with nuts and washers.
▸ Set up the basic sets and connect with the spacer.
▸ Align the basic sets.
▸ Screw tight the basic sets with washers and nuts.
▸ Screw out the two screws facing each other at the cross
members.
▸ Secure the cross members with the upper spacer.
The connecting lines must project at least 50 mm over
the cross member.
▸ Lay the connecting cables and secure to the respective cross
member with the available cable ties.
▸ When mounting on the floor take the mounting
depth into account (→ Fig. C).
▸ Mount the edge insulation strips around the bases and carry
out the floor mounting (example → Fig. A14):
– 1 Edge insulation strips
– 2 Unfinished floor
– 3 Insulation
– 4 Screed
– 5 Tile adhesive
– 6 Tiles
– 7 Silicone (free of acetic acid)
▸ Mount the thermostatic valve externally since
mounting under the radiator is not possible.
B
Wall mounting variant (→ Fig. B1–B10)
▸ Check whether the scope of delivery is complete and free of
damage.
▸ Lay out the required tools.
▸ Mount grommets on the basic set.
The space between the radiator and the finished wall
amounts to 60–110 mm.
▸ Mount the basic set with a space of 81–131 mm,
measured from the base to the finished wall.
▸ Set up the basic set and mark the drill holes.
▸ Drill the holes and insert the screw anchors.
▸ Screw in the hanger bolts with nuts and washers.
▸ Set up the basic set.
▸ Align the basic set.
▸ Screw tight the basic set with washers and nuts.
The connecting lines must project at least 50 mm over
the cross member.
▸ Lay the connecting cables and secure to the cross member
with the available cable ties.
▸ When mounting on the floor take the mounting
depth into account (→ Fig. C).
▸ Mount the edge insulation strips around the bases and carry
out the floor mounting (example → Fig. B10):
– 1 Edge insulation strips
– 2 Unfinished floor
– 3 Insulation
– 4 Screed
– 5 Tile adhesive
– 6 Tiles
– 7 Silicone (free of acetic acid)
▸ Mount the thermostatic valve externally since
mounting under the radiator is not possible.
3