ARIETE Miro 1338 Mode D'emploi page 13

Warning!
As in professional coffee machines, do not remove the filter holder when the brewing is in progress; danger of burns!
Warning!
Wait about ten seconds after the coffee has been dispensed before removing the filter holder; To remove it, turn it
slowly from right to left so as to prevent splashes or spurts of water or coffee.
When the machine is in standby mode, the indicator light of the boiler temperature switch (L) will turn off and turn on a
regular basis, showing the operation of the boiler thermostat, which is needed to maintain the best water temperature. It is
appropriate, for the first coffee for the next ones, to start the coffee brewing, only when this indicator light is on.
how to make coffee with a pod
To make the coffee with a pod it is necessary to remove the filter (A), the silicone disc (B) and the powder coffee dripper
(C) from the filter holder (A).
1 In the filter holder (A) insert the pods dripper (F) and the pod filter (E) (Fig. 17).
2 Place the pod in the filter ring (Fig. 18).
3 Push the pod towards the bottom of the filter with your fingers (Fig. 19).
4 The pod must be well centred and placed inside the filter.
5 Now it is possible to put the filter holder in its seat. Tighten the filter holder while making sure you have hooked it properly
onto the flange (Fig. 7).
6 The pod could remain stuck in the upper part of the machine after making the coffee and when removing filter holder. To
remove it, tilt the filter holder (Fig. 20) so the pod can fall onto it.
To always have a good coffee, you must purchase pods that show the E.S.E. compatibility mark.
if the pod is not inserted well, or if the filter holder is not tightened firmly, a few drops of water could leak from the
filter holder.
filling the water tank during use
It is recommended to fill the water tank before it is completely empty.
Turn off the machine. Unplug it from the socket-outlet. Remove the tank. Fill the tank up to the "MAX" mark with cool tap
water. Place the tank on the machine making sure it is securely inserted in and turn it on again.
In the event that the tank remained completely without water, it can happen that air enters the circuit preventing the flow
of coffee. To reactivate the machine it will be necessary to turn it off and let it cool. Place a container under the filter holder
hooking seat and turn on the machine. Press and hold the steam dispensing button (K). Wait until water flows out of the filter
holder seat (Fig. 5). Drain at least a cup of water from the coupling seat of the filter holder to reactivate the hydraulic circuit.
Release the steam dispensing button to stop the flow of water. At this point the machine will resume normal operation.
MAkIng furTher cups Of cOffee
To prepare a cup of coffee right after making cappuccino, it is necessary to bring the boiler back to the coffee preparation
temperature by performing these operations: press the steam function switch (M). You may notice that the indicator lamp
is on. This luminous indication serves to tell you that the temperature in the boiler is still high, i.e. it is still that for steam;
you must therefore wait a few seconds until the lamp turns off. If you want to cool down the boiler faster, place a container
underneath the cappuccino maker, press switch (L) and at the same time keep the cock (K) open; Make water come out of
the Maxi Cappuccino device until when the indicator lamp turns back on; Now close the cock (K) and turn the switch (O) off.
Wait for the lamp (L) to turn off before making another cup of coffee.
hOW TO MAke cAppuccInO
Press the steam function switch (M). Place a glass under the Maxi Cappuccino device (G), Fig. 12. Wait until the boiler
temperature indicator light of the switch (M) turns on.
in the steam waiting phase small puffs of steam may be released from the flange of the filter holder, this phenome-
non is perfectly normal.
Press and hold the steam dispensing button (K): first a bit of water will come out and immediately after a steam jet whose
intensity increases within a few seconds. Release the steam dispensing button to stop the steam spurt. Place the milk contai-
ner to mount (or liquid to be heated) under the Maxi Cappuccino device (G). Immerse deeply the stylus into the milk jug (Fig.
13) and press again the button (K) until you obtain the desired result. During these operations, you will see that the boiler
temperature indicator light of the switch (M) turns on and off periodically, indicating the action of the thermostat which main-
tains the proper temperature of the boiler for steam dispensing. Release the steam dispensing button to stop the steam spurt.
it is opportune you start dispensing the steam only when this indicator lamp (m) is on. dispense the steam for a
13