Publicité
Operation
Starting up the device
Put the tool into operation as described in the chapter „Placing into
Note
operation".
Please adhere to the
Check to see if the mains voltage matches the ratings on the name-
operating instructions of the
plate.
connected devices.
Make sure the machine is switched off before plugging in.
Soldering and desoldering
Carry out soldering work as directed in the operating instructions of
Caution!
your connected soldering tool.
Always make sure that the
Handling the soldering tips
soldering tips are fitted
Coat the selective and tinnable soldering tip with solder when
„
properly.
heating it up for the first time. This removes oxide coatings which
The control units have been
have formed during storage and impurities from the soldering tip.
adapted to hold a medium-
Make sure that the soldering tip is well coated with solder during
„
sized soldering tip.
breaks between soldering work and prior to storage of the device.
Discrepancies may occur if
Do not use aggressive fluxing agents.
„
the tip is changed or a
Always make sure that the soldering tips are fitted properly.
different shaped tip is used.
„
Select as low a working temperature as possible.
„
Select the largest possible soldering tip shape for the application.
„
Rule of thumb: the soldering tip should be roughly as large as the
soldering pad.
Coat the soldering tip well with solder to ensure that there is
„
efficient heat transfer between the soldering tip and the soldering
area.
Prior to extended breaks between soldering work, switch off the
„
soldering system or use the Weller function to reduce the
temperature when the soldering equipment is not in use.
Coat the tip with solder prior to storage if you do not intend to use
„
the soldering iron for an extended period of time.
Apply solder directly to the soldering area, not to the soldering
„
tip.
Change the soldering tips using the designated tool.
„
Do not apply mechanical force to the soldering tip.
„
14
Guía de menú
Tiempo standby (desconexión de la temperatura)
2 sec
Reducción de la temperatura de referencia ajustada a
150°C (300°F) (standby).
El tiempo setback, tras que cual la estación de soldar pasa
al modo standy, se puede ajustar entre 0 y 99 minutos
(0=OFF). El estado setback se muestra mediante un valor real
intermitente y finaliza al pulsar una tecla. En este caso se muestra
brevemente el valor de referencia ajustado. Una vez transcurrido
tres veces el tiempo setback se activa la función „Auto off". El solda-
dor se desconecta (raya intermitente en el indicador).
Offset (offset de temperatura)
4 sec
La temperatura real de la punta del soldador se puede
ajustar introduciendo un offset de temperatura de aproxi-
madamente ± 40 °C (± 72 °F).
Unidad de medición de la temperatura °C/°F
6 sec
Cambiar la unidad de temperatura de °C a °F o viceversa.
Contraseña (función de bloqueo)
8 sec
Bloqueo de la temperatura de referencia. Una vez realizado el
bloqueo ya no se pueden realizar modificaciones en la estación de
soldar.
Bloqueo/Desbloqueo de la estación de soldar: introducir el código (1-999)
mediante las teclas Subir/Bajar. Mantener pulsadas al mismo tiempo las
teclas Subir/Bajar durante 3 segundos para confirmar la operación.
En caso de pérdida del código de acceso póngase en contacto con el
Servicio de Atención al Cliente de Weller. (technical-service@weller-tools.
com)
Rango de temperatura (WINDOW)
10 sec
Limitación del rango de temperatura a un máx. de ± 99
°C (178 °F) a partir de una temperatura bloqueada con la
función „LOCK".
Por tanto la temperatura bloqueada representa el centro
del rango de temperatura ajudtable.
configuración de fábrica
12 sec
Reseteo de los valores ajustados a 0, temperatura 350°C / 660°F.
Mantener pulsadas al mismo tiempo las teclas Subir/Bajar durante 3
segundos para confirmar la operación.
15
Publicité
