Set-Up Codes; Washer Diagnostic Mode - Whirlpool 3LCHW9100WQ Instructions D'installation

Set-up Codes

■ The WOOLENS key pad will advance you from code to code.
■ The PERM PRESS key pad will change the code value.
■ The DELICATES/KNITS key pad will select or deselect
options.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
CODE EXPLANATION
7 9 WASH LENGTH
7 9 This is the number of minutes for WASH. Washer
comes from the factory preset with 9 minutes.
Choose from 9-17 minutes by pressing the PERM
PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.
8 00 ADDITIONAL RINSE OPTION
This option is either SELECTED "ON" or
NOT SELECTED "OFF."
8 00 Not Selected "OFF."
8 Ar Selected "ON." Cannot be combined with the
Super Cycle rinse option.
Press the DELICATES/KNITS key pad once for this
selection.
Press the WOOLENS key pad once to advance
to next code.
9 00 CYCLE COUNTER OPTION
This option is either SELECTED "ON" or
NOT SELECTED "OFF."
9 00 Not Selected "OFF."
9 0C Selected "ON" and not able to be deselected.
Press the DELICATES/KNITS key pad
3 consecutive times to select "ON." Once selected
"ON" it cannot be deselected.
Press the WOOLENS key pad once to advance
to next code.
CODE EXPLANATION
5. 00 TIME-OF-DAY CLOCK, MINUTES
5. 00 This is the TIME-OF-DAY CLOCK, minute setting;
select 0-59 minutes by pressing the PERM PRESS
key pad.
Press the WOOLENS key pad once to advance
to next code.
6. 00 TIME-OF-DAY CLOCK, HOURS
NOTE: Uses the 24 hr. clock
6. 00 This is the TIME-OF-DAY CLOCK, hour setting;
select 0-23 hours by pressing the PERM PRESS
key pad.
Press the WOOLENS key pad once to advance
to next code.
r. 800 TOP SPIN SPEED RPM
r. 800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds by
pressing the PERM PRESS key pad. Factory pre-
set for 800 rpm.
Press the WOOLENS key pad once to advance
to next code.
A1. 00 PREWASH LENGTH
A1. 00 This is the number of minutes of PREWASH.
Choose 0 to disable the prewash or select between
2 and 7 minutes by pressing the PERM PRESS key
pad.
Press the WOOLENS key pad once to advance
to next code.
A2. 03 FINAL SPIN LENGTH
A2. 03 This is the number of minutes of final high speed
spin. Choose from 3-8 minutes by pressing the
PERM PRESS key pad.
Press the WOOLENS key pad once to advance
to next code.
If cycle counter (9 0C) is selected, the following is true:
1 00 Number of cycles in
HUNDREDS.
2 00 Number of cycles in ONES.
This is "VIEW ONLY" and cannot be cleared.
Press the WOOLENS button once to advance to
next code.
EXIT FROM SET-UP MODE
Remove power, open console, reinsert plug into AA1, close console,
and apply power.

Washer Diagnostic Mode

To enter the "Washer Diagnostic Mode," first enter "Start
Operating Set-up." Then press and hold the DELICATES/KNITS
key pad for 1 second while in set-up code 6, anytime a
diagnostic code is present.
On entry to diagnostic mode the entire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diagnostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options
are permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. Washer Cleanout cycle - With the entire display flashing, this
cycle is started by pressing the BRIGHTS key pad.
Use the Washer Cleanout cycle once a month to keep the
inside of your washer fresh and clean. This cycle uses a
higher water level. Use with liquid chlorine bleach to
thoroughly clean the inside of the washer. This cycle should
not be interrupted.
IMPORTANT: Do not place garments or other items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
1 02 = 200
2 25 = 25
TOTAL CYCLES = 225 cycles
11