Publicité
Les langues disponibles
Les langues disponibles
EN
b) Do not use the power tool in a dangerous workplace containing combustible or explosive materials (flamma
ble liquids, gases or dust). Due to fact that the power tool produces sparks during work it may be the cause
for ignition.
c) Keep children and third parties away from work area.
2.4 Power tool handling and operation
a) Please do not overload the device! Only use suitable setting tools when operating the power tool.
b) Do not use the power tool if the switch is broken. Usage of such device is dangerous and needs to be
repaired first.
c) Always pull out the plug from the power outlet when changing accessories, making any adjustments or after
work. This precautionary measure prevents the unintentional start of the power tool.
d) Store idle equipment out of the reach of children. Do not let people who are not familiar with the device
operate the power tool.
e) Perform regular maintenance of power tool. It is recommended to check regularly the moving parts of the
tool (whether they are blocked, cracked or show signs of any other damage that may cause unsafe use of
the power tool). In that case all affected parts must be replaced. Improper maintenance of power tools is a
common cause of accidents.
f)
The use of power tools, gears, accessories, etc., must be in accordance with these guidelines and instructions.
The user must keep in mind the conditions under which the work takes place and the nature of the job. Using
this tool for purposes other than stated above can result in serious work accidents.
2.5 Service / Repair
In order to ensure safe use of this power tool, any repairs should be entrusted only to a qualified technician. This will
ensure the use of original spare parts.
3. DETAILED RULES OF SAFETY
3.1. Wet Stone Polisher MSW – WET900L / MSW – WET900S:
•
Accessories used with this tool must be rated for at least 4000 RPM.
•
Check backer pad end polishing discs for damage before operating replace damaged pad/discs immediately prior to
use.
•
When using tool, always wear safety glasses.
•
Do not use this tool with wood or metal cutting blades.
•
Hold tool firmly at all times.
•
Keep hands away from moving parts.
•
Make sure the work piece is adequately supported.
•
Do not touch work place immediately after polishing. It may be very hot.
•
Wear rubber gloves and boots for protection against electric shock.
•
Make sure that no water is entering the motor.
Always use a Ground Fault Circuit Interrupter (GFCI) with this tool.
3.2. Burnishing Machine MSW – BUR900S:
The power tool must be held by the isolated handles. In some situations, the power cord may be damaged by the sanding
disc; this may lead to cases when the metal parts of the power tools will be under voltage. This is very dangerous while the
operator may get an electric shock.
When sanding metal, electric sparks may occur. During work please ensure that nobody is in the danger area. Due to the
danger of fire, all combustible and flammable materials should be removed from the workplace.
Regularly clean the power tool by blowing compressed air through the ventilation slots. Rotating motor draws dust into
the interior of the power tool, and an accumulation of metal dust may cause an electric shock hazard.
There are some factors that may be a threat to health:
•
dust coatings containing lead
•
dust of certain species of wood / minerals (oak and beech dust in conjunction with substances for woodworking are
carcinogenic)
•
certain types of metal powders
•
Avoid physical contact with all environmental impacts mentioned above as inhalation of the dust may cause allergies
or respiratory disease.
•
Asbestos and materials containing asbestos can be handled only by persons trained in this field.
•
If it is possible, the dust extraction devices should be used.
8
•
The work place must be well ventilated.
•
The use of a dust mask of filter class P2 is recommended.
National requirements for the treatment materials you want to work with must be followed.
Processed material should be securely and properly fastened. Do not hold the workpiece in hands – it is safer to secure
the item in the mounting bracket / vise.
The power tool should always be guided with both hands holding the appropriate handles. Loss of control of the power
tool may result in personal injury.
Hands must be kept away from rotating parts or the sanding belt of the power tool.
Removing dust from sanding can be performed only if the device is switched off and disconnected from the power source.
Before any activities related to the adjustment, tapes replacement or servicing, please unplug the power cord from the
power outlet.
Technical specification:
Model
Power
Polishing disc diameter
Durchmesser der Polierscheibe
Abrasive tool diameter
Abrasive tool width
4. OVERVIEW
MSW-WET -900L
Wet polisher with water supply line and hose adapter,
Splash guard
Ground fall circuit interrupter (GFCI)
Shaft wrench (2)
Side handle & U-Handle
Gearbox cover
Carbon brush
MSW-WET -900S
Wet polisher with water supply line and hose adapter
Splash guard
Ground fall circuit interrupter (GFCI)
Shaft wrench (2)
U-Handle (with 2 attachment bolts)
Carbon brush
MSW-BUR900S
Handle
Carbon brush
Wrench
Rev. 17.02.2022
Rev. 17.02.2022
MSW-WET-900L
MSW-WET-900S
900W
900W
700-3000RPM
1000-4000RPM
5"Max
5"Max
-
-
-
-
EN
MSW-BUR900S
-
700-3000RPM
-
4-4½"
2-4"
9
Publicité
