Metabo CS 23-355 Notice Originale page 11

Original instructions
6284162841
1. Conformity Declaration
We declare under our sole responsibility: These
metal chop saws, identified by type and serial
number *1), comply with all relevant requirements of
the directives *2) and standards *3). Technical file
at *4) - see page 3.
2. Specified Use
When fitted with original Metabo cutting discs, the
metal cutter is appropriate for dry cutting of steel,
non-ferrous metals, iron and cast moulds, and
similar materials.
Do not use diamond cut-off wheels.
The user bears sole responsibility for damage
caused by improper use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.
3. General Safety Instructions
For your own protection and for the
protection of your electrical tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating instruc-
tions will reduce the risk of injury.
WARNING – Read all safety warnings,
instructions, illustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference. Pass on your electrical tool only
together with these documents.
4. Special Safety Instructions
4.1 Cut-off machine safety warnings
a) Position yourself and bystanders away from the
plane of the rotating wheel. The guard helps to
protect the operator from broken wheel fragments
and accidental contact with wheel.
b) Use only bonded reinforced cut-off wheels for
your power tool. Just because an accessory can be
attached to your power tool, it does not assure safe
operation.
c) The rated speed of the accessory must be at
least equal to the maximum speed marked on the
power tool. Accessories running faster than their
rated speed can break and fly apart.
d) Wheels must be used only for recommended
applications. For example: do not grind with the side
of a cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces applied
to these wheels may cause them to shatter.
e) Always use undamaged wheel flanges that are of
correct diameter for your selected wheel. Proper
wheel flanges support the wheel thus reducing the
possibility of wheel breakage.
f) The outside diameter and the thickness of your
accessory must be within the capacity rating of your
power tool. Incorrectly sized accessories cannot be
adequately guarded or controlled.
g) The arbour size of wheels and flanges must
properly fit the spindle of the power tool. Wheels
and flanges with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
h) Do not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If the power
tool or wheel is dropped, inspect for damage or
install an undamaged wheel. After inspecting and
installing the wheel, position yourself and
bystanders away from the plane of the rotating
wheel and run the power tool at maximum no load
speed for one minute. Damaged wheels will
normally break apart during this test time.
i) Wear personal protective equipment. Depending
on application, use face shield, safety goggles or
safety glasses. As appropriate, wear dust mask,
hearing protectors, gloves and shop apron capable
of stopping small abrasive or workpiece fragments.
The eye protection must be capable of stopping
flying debris generated by various operations. The
dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged
exposure to high intensity noise may cause hearing
loss.
j) Keep bystanders a safe distance away from work
area. Anyone entering the work area must wear
personal protective equipment. Fragments of
workpiece or of a broken wheel may fly away and
cause injury beyond immediate area of operation.
k) Position the cord clear of the spinning accessory.
If you lose control, the cord may be cut or snagged
and your hand or arm may be pulled into the
spinning wheel.
l) Regularly clean the power tool's air vents. The
motor's fan can draw the dust inside the housing
and excessive accumulation of powdered metal
may cause electrical hazards.
m) Do not operate the power tool near flammable
materials. Do not operate the power tool while
placed on a combustible surface such as wood.
Sparks could ignite these materials.
n) Do not use accessories that require liquid
coolants. Using water or other liquid coolants may
result in electrocution or shock..
4.2 Kickback and related warnings
Kickback is a sudden reaction to a pinched or
snagged rotating wheel. Pinching or snagging
causes rapid stalling of the rotating wheel which in
turn causes the uncontrolled cutting unit to be
forced upwards toward the operator.
ENGLISH en
11