Quick ANTARES AT 1012 Manuel De L'utilisateur page 17

POS. DESCRIPTION
17 Mooring rope puller
18 Spring for pressure lever
19 Mooring rope puller pin
20 Pressure lever
21 Screw
22 Rope/chain stripper stainless steel MSN10ATX0000
23 Sensor
24 Gypsy lock pin
25 Screw
26 Gypsy lock lever control
27 Gypsy lock lever
28 Gypsy lock spring
29 Chain guide cover
30 Cover pin
31 Base
32 Gasket / jig Antares
33 Stud
34 Gearbox flange gasket Top TG50
35 Gearbox flange gasket Top TG60
36 Gearbox 700/1000W Quick TG50
37 Gearbox 1500W Quick TG70
38 Washer
39 Spring washer
40 Nut
41 Washer
42 Self-locking nuts
43 O-ring 700/1000W
44 O-ring 1500W
45 Key
46A Electric motor 1000W 12V
46B Electric motor 1000W 24V
46C Electric motor 1500W 12V
46D Electric motor 1500W 24V
47 Motor casing watertight 1000W
48 Grommet 1000W
49 Terminal board cover 1000W
50 Screw
51 Bottom gasket 1000W
52 Bottom protec cover 1000W
53 Cable outlet
54 Screw
ANTARES 1000/1500W - REV007B
CODE
MMSTTC10ATC0
MMTND10ATC00
MMTC10ATC000
Quick
PDLVTD10ATCN
ant to marine environments. In any case, any salt deposits
MBV0612MXCE0
on the outside must be removed periodically to avoid corro-
sion and damage to the equipment.
SAKREED00000
The parts where salt may have built up should be washed
MSVPR10ATC00
thoroughly with fresh water.
MBV0412MXTSC
PVLBBATC0000
Once a year, the drum and the gypsy are to be taken apart
SGMSH10ATC00
as follows:
MMBLBRATC000
SGMSGG10ATC0
DRUM VERSION
MSR10XATC000
Use the handle (1) to loosen the bush (2); pull off the drum
SGMSC10ATC00
(5) and the top clutch cone (4); loosen the fixing screws (21)
PGBSG10AT000
of the rope/chain stripper (22) and remove it. Pull off the
MBP080807X00
gypsy (6).
PGFLRDTG5000
NO-DRUM VERSION
PGFLRDTG6000
MR1000000000 Use the handle (1) to loosen the bush (2) and the screws
(53); to remove the gypsy cover (3); and the top clutch cone
SLMR15TG7000
(4); loosen the fixing screws (21) of the rope/chain stripper
MBR08X000000
(22) and remove it. Pull off the gypsy (6).
MBR08XDE0000
MBD08MXEN000
Clean all the parts removed to avoid corrosion, and grease
MBR061815X00
the shaft thread (13 or 15) and the gypsy (6) where the
MBD06MXET000
clutch cones rest (4 and 7) (use grease suitable for marine
-
environment).
-
MBH050515F00
Remove any oxide deposits from the terminals of the elec-
EMF101200000
tric motor and the contactor unit; grease them.
EMF102400000
EMF151200000
EMF152400000
PCCCPM100000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
MBV0616MXCE0
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17 17