First Lighting; Fuel; Recommended Fuels; Forbidden Fuels - deville C077AR Notice D'installation Et D'utilisation

Your stove is a real heating appliance :
•
High output.
•
Slow speed running for a long period of time.

5.1 - First lighting

•
After the building of the fireplace and the setting up
of the appliance, a drying period of the materials
used for the work has to be respected (2 to 3
weeks).
•
Do not connect the stove to a pipe linked to several
appliances.
•
After the first lighting (see paragraph 5.4.1), make
a moderate fire in the first hours limiting the loading
in the appliance (a log of ∅ 15 cm) with the air
intake damper in an intermediate position (see
paragraph 5.4.2) : progressive rise in temperature
of all the elements of the fireplace and normal
expansion of the appliance.
•
During the first uses, a paint odor can come out
from the appliance : ventilate the room to limit this
inconvenience..

5.2 - Fuel

5.2.1 – Recommanded fuel
Hard wood : oak, hornbeam, beech, chestnut tree, etc...
in log of 50 cm (56 cm max) long.
Maximum loading height: 20 cm.
We recommend you to use very dry wood (20 %
maximum humidity), that is a 2-year store under shelter
after cutting, to get better outputs and to avoid the
darking of the smoke flue and of the windows. Avoid
the use of conifers (pines, firs, spruces...) which ask for
a more frequent cleaning of the appliance and the flue.
5.2.2 – Forbidden fuels
All fuels except wood are forbidden, especially coal and
its by-products.
Fires with twigs, twinings, small boards, straw,
cardboard are dangerous and banned.
The appliance must not be used as a waste incinerator.

5.3 - Use of the operation parts and equipment

Air inlet damper (Fig. 9) : move using the poker.
Door handle : move using the poker (Fig. 6) or an oven
glove.
Nozzle flap control : move using the poker (Fig. 6) or
an oven glove.
Scraper (Fig. 7) : for ash removal and appliance
cleaning.
Don't take the risk of burning your hands, use the fire
irons.
LIGHTING REGISTER (Fig. 9)
Lighting position is obtained by moving the damper
directly with your hand : this position must only be used
when the stove is "cold". It cannot be maintained more
than 30 minutes. You must keep a close eye on the
stove during the lighting stage. To reach this position,
you must follow the following steps (position C Fig.9) :
•
Operation n°1:
Pull the primary
corresponding to the "Maximum power" position
lock.
•
Operation n°2:
Lift the adjustment lever.
•
Operation n°3:
Pull the lever to its maximum height: you are in the
"Lighting" position.
Once lit, return to the maximum power, intermediate
power, or minimum power position, use the poker to
push the air intake regulation lever which may be hot.

5.4 - Use

5.4.1 - Lighting

•
Open the air intake regulation lever to the lighting
position (position C Fig. 9) and turn the nozzle flap
to the open position (position D Fig. 9), the nozzle
flap control is parallel to the nozzle axis.
•
Place crumpled paper and small and very dry parts
of wood (twigs) on the grate, then place branches
of split wood of a bigger size (∅ 3 à 5 cm).
•
Light the paper and shut the door (leave it slightly
open to accelerate the lighting in avoiding any
blowing back outside the appliance).
•
When the loading of small parts of wood is well lit,
open the door, load the appliance with the
recommended fuel and use the regulation devices
to obtain the burning required. Turn the nozzle flap
to the closed position (position E Fig. 9), the nozzle
flap control is perpendicular to the nozzle axis.

5.4.2 - Working

5.4.2.1 Intermittent use
The intermittent use of the appliance requires a
reload every 45 minutes.
This type of use is particularly recommended as
it environmentally friendly.

5.4.2.2 Fire duct

• The required power is regulated using the air
intake lever (Fig. 1 Part no. 6) and by selecting a
load that corresponds to your needs.
14
air lever until the stop