Murray 6331770X54 Manuel De L'utilisateur page 13

How To Adjust The Traction Drive Cable
1. Remove the gas from the gas tank. Stand
the snow thrower up on the front end of the
auger housing.
WARNING: Drain the gasoline
outdoors, away from fire or flame.
2. (Figure 22) Loosen the bolts (3) on each
side of the bottom panel (2).
3. Remove the bottom panel (2).
4. (Figure 16) Disconnect the "Z" fitting (1)
from the traction drive lever (2).
5. (Figure 27) Slide the cable boot (3) off the
cable adjustment bracket (4).
6. Push the bottom of the traction control
cable (5) through the cable adjustment
bracket (4) until the "Z" hook (6) can be
removed.
7. Remove the "Z" hook (6) from the cable
adjustment bracket (4). Move the "Z" hook
(6) down to the next adjustment hole.
8. Pull the traction control cable (5) up
through the cable adjustment bracket (4).
9. Put the cable boot (3) over the cable
adjustment bracket (4).
10. (Figure 16) Install the "Z" fitting (1) to the
traction drive lever (2).
11. (Figure 15) To check the adjustment,
depress the drive lever and check the length
"A" of the drive spring (7). In correct
adjustment, the length "A" of the drive
spring (7) is as follows:
minimum 3 inches (76 mm)
maximum 3-3/8 inches (85 mm).
12. (Figure 22) Install the bottom panel (2).
13. Tighten the bolts (3) on each side of the
bottom panel (2).
How To Adjust The Belts
The belts will stretch during normal use. If you
need to adjust the belts due to wear or stretch,
proceed as follows.
How To Adjust The Auger Drive Belt
If the snow thrower will not discharge snow,
check the adjustment of the auger drive cable.
See "How To Check And Adjust The Cables" in
the Maintenance section. If the adjustment is
correct, then check the condition of the auger
drive belt. If the auger drive belt is damaged,
replace the auger drive belt. See "How To
Replace The Belts" in the Maintenance section.
If the auger drive belt is loose, adjust as follows.
1. Disconnect the spark plug wire.
2. (Figure 18) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
3. (Figure 19) Loosen the nut (2) on the idler
pulley (3) Move the idler pulley (3) 1/8 inch
(3 mm) toward the auger drive belt (4).
4. Tighten the nut (2).
5. (Figure 21) Depress the auger drive lever.
Check the tension on the auger drive belt
(4). In correct adjustment, the auger drive
belt (4) will deflect 1/2 inch (12.5 mm) (5)
with moderate pressure. If the adjustment is
not correct, repeat the adjustment.
6. (Figure 18) Install the belt cover (1). Tighten
screw (2).
7. Check the adjustment of the auger drive
cable. See "How To Check And Adjust The
Cables" in the Maintenance section.
8. Attach the spark plug wire.
1740880
Traction Drive Belt
The traction drive belt has constant spring
pressure and does not require an adjustment. If
the traction drive belt is slipping, replace the
belt. See "How To Replace The Belts" in the
Maintenance section.
How To Replace The Belts
The drive belts are of special construction and
must be replaced with original factory
replacement belts available from your nearest
authorized service center.
Some steps require the assistance of a second
person.
How To Remove the Auger Drive Belt
If the auger drive belt is damaged, the snow
thrower will not discharge snow. Replace the
damaged belt as follows.
1. Disconnect the spark plug wire.
2. (Figure 22) Remove the bolts (1) on each
side of the bottom panel (2).
3. Loosen the bolts (3) on each side of the
bottom panel (2).
4. Remove the bottom panel (2).
5. (Figure 18) Remove screw (2) from belt
cover (1). Remove the belt cover (1).
6. (Figure 19) Loosen the belt guide (9). Pull
the belt guide (9) away from the auger
drive pulley (10).
7. Pull the idler pulley (3) away from the auger
drive belt (4) and slip the auger drive belt
(4) off of the idler pulley (3).
8. Remove the auger drive belt (4) from the
engine pulley (11). To remove the auger
drive belt (4), the engine pulley (11) may
have to be partially rotated.
9. (Figure 20) Remove the top four bolts (21)
that hold together the auger housing (22)
and the motor box (23). Loosen the bottom
two bolts (24). The auger housing (22) and
the motor box (23) can now be split apart for
removal of the belt.
10. (Figure 19) Remove the old auger drive
belt (4) from the auger drive pulley (10).
Replace the auger drive belt (4) with an
original factory replacement belt available
from an authorized service center.
11. Install the new auger drive belt (4) onto the
auger drive pulley (10).
NOTE: To assemble the auger housing
(22) to the motor box (23), have someone
hold the auger clutch lever in the
ENGAGED position. This will move the
idler arm and pulley (3) enough to allow
the auger drive pulley (10) to move back
into position.
12. Assemble the auger housing (22) to the
motor box (23) with the four bolts (21) that
were removed in step 9. Tighten the bottom
two bolts (24).
13. Install the auger drive belt (4) onto the
engine pulley (11).
14. Slip the auger drive belt (4) under the idler
pulley (3).
15. Adjust the auger drive belt (4). See "How To
Adjust The Auger Drive Belt" in the
Maintenance section.
16. Adjust the belt guide (9). See "How To
Adjust The Belt Guide" in the Maintenance
section.
13
17. (Figure 18) Install the belt cover (1). Tighten
screw (2).
18. (Figure 22) Install the bottom panel (2).
19. Install the bolts (1) on each side of the
bottom panel (2).
20. Tighten the bolts (1) and bolts (3) on each
side of the bottom panel (2).
21. Check the adjustment of the cables. See
"How To Check And Adjust The Cables" in
the Maintenance section.
22. Connect the spark plug wire.
How To Remove the Traction Drive Belt
If the snow thrower will not move forward, check
the traction drive belt for wear or damage. If the
traction drive belt is worn or damaged, replace
the belt as follows.
1. Disconnect the spark plug wire.
2. Remove the auger drive belt. See "How To
Remove The Auger Drive Belt" in the
Maintenance section.
3. (Figure 19) Remove the e−ring (17) from
one end of the swing plate axle rod (18).
Remove the swing plate axle rod (18) to
allow the the swing plate to pivot forward.
4. Remove the traction drive spring (16).
5. Remove the old traction drive belt (13) from
the traction drive pulley (14) and from the
engine pulley (15). Replace the traction
drive belt (13) with an original factory
replacement belt available from an
authorized service center.
6. Install the new traction drive belt (13) onto
the traction drive pulley (14) and onto
engine pulley (15).
7. Make sure the traction drive idler pulley
(12) is properly aligned with the traction
drive belt (13).
8. Attach the traction drive spring (16).
9. Install the swing plate axle rod (18) and
secure with the e−ring (17) removed earlier.
10. (Figure 32) The bottom of the swing plate
(20) must be positioned between the
alignment tabs (19). Make sure the swing
plate (20) is properly secured.
NOTE: If the drive will not engage after
the traction drive belt has been replaced,
then check to make sure that the swing
plate is positioned between the alignment
tabs (19).
11. (Figure 19) Install and adjust the auger
drive belt (4). See "How To Remove The
Auger Drive Belt" in the Maintenance section.
12. Adjust the belt guide (9). See "How To
Adjust The Belt Guide" in the Maintenance
section.
13. (Figure 22) Install the bottom panel (2).
14. Tighten the bolts (3) on each side of the
bottom panel (2).
15. (Figure 18) Install the belt cover (1). Tighten
screw (2).
16. Check the adjustment of the cables. See
"How To Check And Adjust The Cables" in
the Maintenance section.
17. Connect the spark plug wire.
How To Adjust The Belt Guide
1. Disconnect spark plug wire.
2. (Figure 18) Remove screw (2). Remove the
belt cover (1).
3. (Figure 1) Engage the auger drive lever (5).
4. (Figure 23) Measure the distance between
the belt guide (2) and auger drive belt (3).
The correct distance (4) is 1/8 inch (3 mm).
en