Bosch GIC 120 C Notice Originale page 13

OBJ_BUCH-2385-001.book Page 13 Monday, March 2, 2015 10:30 AM
Technical Data
Digital Inspection Camera
Article number
Rated voltage
– with battery pack
– with batteries
With battery pack
With battery adapter (removable)
With battery adapter (not removable)
Batteries (alkali-manganese)
Operating temperature
Storage temperature (hand unit without battery pack or battery
adapter)
Relative humidity
Smallest bending radius of camera cable
Diameter of camera head
Display resolution
Operating time, approx.
Weight according to EPTA-Procedure 01/2003
Dimensions (length x width x height)
1) Free of moisture condensation
2) with batteries
3) with battery pack at 100 % brightness of the illumination light in the camera head
Assembly
Power Supply
The inspection camera can be operated either with commer-
cially available non-rechargeable batteries or with a Bosch
lithium-ion battery.
Operation with Battery Adapter (Removable)
(3 601 B41 2..) (see figure A)
The batteries are inserted into the battery adapter.
 The battery adapter is intended only for use in desig-
nated Bosch inspection cameras and must not be used
with power tools.
To insert the batteries, slide the cover 26 of the battery
adapter into the port 28. Place the batteries in the cover as
per the illustration on the sealing cap 27. Slide the sealing cap
over the cover until you feel it engage and it is flush with the
handle of the inspection camera.
To remove the batteries, press the unlocking buttons 18 of
the sealing cap 27 and pull off the sealing cap. Pull the inside
cover 26 out of the port 28.
Always replace all batteries at the same time. Only use batter-
ies from one brand and with the identical capacity.
 Remove the batteries from the inspection camera
when not using it for a prolonged period of time. The
batteries can corrode and self-discharge during prolonged
storage.
Bosch Power Tools
GIC 120 C
3 601 B41 2..
V= 10.8
V= 6.0
4 x 1.5 V LR6 (AA)
°C –10...+50
°C –20...+60
% 5–95
mm 25
mm 8.5
320 x 240
2)
h 2 /6
kg 0.6
mm 217 x 90 x 49
Operation with Battery Pack (3 601 B41 2..)
(see figure B)
 Use only original Bosch lithium-ion batteries with the
voltage listed on the nameplate of your inspection cam-
era. Using other batteries can lead to injuries and pose a
fire hazard.
 Use only the battery chargers listed on the graphics
page. Only these battery chargers are matched to the lith-
ium-ion battery used in your inspection camera.
Note: Using batteries not suitable for your inspection camera
can lead to malfunctions or damage the inspection camera.
Note: The battery pack is supplied partially charged. To en-
sure full capacity of the battery pack, completely charge the
battery pack in the battery charger before using for the first
time.
The lithium-ion battery pack can be charged at any time with-
out reducing its service life. Interrupting the charging proce-
dure does not damage the battery pack.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
To insert the charged battery pack 17, slide it into the port 28
until you feel it engage and it is flush with the handle of the in-
spection camera.
To remove the battery pack 17, press the unlocking buttons
18 and pull the battery pack out of the port 28. Do not exert
any force.
English | 13
GIC 120 C
3 601 B41 270
–
6.0

–

–

–
4 x 1.5 V LR6 (AA)
–10...+50
–20...+60
1) 1)
5–95
25
8.5
320 x 240
3) 2)
2
0.6
217 x 90 x 49
1 609 92A 124 | (2.3.15)