Publicité
Les langues disponibles
Les langues disponibles
4
installation
For your own and for other people's safety, carefully
follow the "Safety Regulations" in section 3.
4.1 Packaging
The original packaging has been designed to protect the
machine during transport. We recommend keeping the
packaging for future transport.
4.2 installation instructions
Before installing the machine, read the following safety
instructions carefully:
• Place the machine in a safe place;
• Make sure children cannot play with the machine;
• Do not place the machine on hot surfaces or near open
flames.
The coffee machine is now ready to be connected to the power
supply.
Note: It is recommended that machine parts be
washed before their first use and/or after they
have not been used for a period of time.
4.3 machine connection
Electric power can be dangerous! It is therefore
essential to follow the safety regulations
carefully. Never use faulty cords! Faulty cords and plugs
must be immediately replaced by authorized service
centers.
Appliance voltage has been pre-set by the manufacturer.
Check that the power voltage matches the indications on the
identification plate located on the bottom of the appliance.
• Check that the ON/OFF button (17) is not pressed before
connecting the machine to the power supply.
• The power cord is located inside the machine. Follow the
instructions in section 4.4 to lift the water tank.
(Fig.3) - Place the power cord correctly, so that it does not
interfere with the water tank.
• Fit the plug into a wall socket with suitable power
voltage.
4.4 Water tank
• (Fig.1) - Remove the cover from the water tank (4).
• (Fig.2) - Lift the suction pipe and remove the water tank
(5); make sure not to damage the water suction pipe.
• (Fig.4) - Rinse the tank and fill it with fresh drinking water
taking care not to overfill.
• (Fig.5) - Lift the suction pipe and fit the tank back into its
housing.
• (Fig.6) - Correctly replace the water suction pipe into the
tank; and place the cover back onto the tank.
Only use fresh, non-sparkling drinking water
to fill the tank. warm or hot water, or any
other liquid, may damage the tank. Do not turn on the
machine with empty water tank: always make sure
there is enough water in the tank.
4.5 Priming the Water circuit
Before starting up the machine, after a long inactivity and
when all the water has been dispensed, the machine's water
circuit must be primed.
• (Fig.7) - Press the ON/OFF button (17).
• (Fig.8) - Place a container below the steam spout. Open
the hot water/steam knob (3) by turning it counter-
clockwise and press the brew button (15).
• Wait until a steady jet of water flows out of the steam
spout (Pannarello).
• Push the button (15) and close the hot water/steam knob
(3) by turning it clockwise.
At first use of the machine and after long
periods of inactivity, the water circuit should
be rinsed.
4.6 Water circuit rinsing
This simple operation ensures an optimum brewing and must
be performed:
- at first start-up;
- if the machine is to remain inactive for a long time.
• (Fig.8) - Place a container under the steam wand
(Pannarello). Open the knob (3) by turning it counter-
clockwise and press the brew button (15).
• Dispense half the water tank content from the steam / hot
water wand. To end the operation, press again the brew
button (15) and close the knob (3) by turning it clockwise.
• (Fig.11 - 12) - Insert the Portafilter into the brew unit
from the bottom (7) and turn it from left to right until it
locks into place.
• Place a suitable container under the Portafilter.
• Press the brew button (15) and dispense all the water left
in the water tank. Once the tank is empty, stop dispensing
by pressing the brew button again (15).
• Fill the tank again and wait until the "machine ready"
brew button (15) turns on.
• 17 •
Publicité
