Technical Features - Eckerle SP32/01 Instructions De Montage Et De Mise En Service

Technical Features

ELECTRICAL
TYPE
Voltage
SP32 /01 230 V
Function, Application and Installation advice
The fuel oil suction pump assembly SP32-01 is intended for the supply
of fire places, ovens and automatic oil burners with fuel oil L, EL accor-
ding to DIN 51603 in the suction operation. The device lifts the fuel oil up
to a max. height of 7m and fills up the integrated 1.6l tank automatically.
The supply to the appliance device can pursue in the inlet operation with
natural downward gradient (minimum 2%) or in the suction operation
from the oil burner pump. The pump takes over then the function of an
intermediate storage and/or a station.
Do not install any check valve as well as a suction filter in the suction
line. It´s already built inside the pump. If a filter or check valve are instal-
led on the suction line the suction height will be affected. The built-in,
open reservoir works as a oil ventilation. Therefore, no additional venti-
lation on the consuming device is necessary. Sketches of the installation
options of the SP32-01 you will find on page 2.
1.Technical Equipment
Electromagnetic piston pump, filter cartridge, thermal safety monitoring,
central detection system linked to pre-programmed PCB, LED display
for function and breakdown information, two lines adapters with cutting
ring threaded connection 8 x 1 mm and accessory installation material.
The 1.6l storage tank, piston pump as well as the hydraulic connectors
are installed over the integrated secutity oil catch pan. It is monitored
electronically by a leakage safety control floater. The SP32-01 arrives
fully assembled and factory tested.
2.Approvals and Safety Features
The equipment is approved and certified according to DIN 4736, built
according to VDE 0722, radio protection – N, EN 12514-2, EN 60335-1
und EN 55015-1. The pump has an oil deficiency safety device as well
as a leakage monitoring for the safety catch pan. In addition, a time-ope-
rated control systems supervise the function of the integrated piston
pump.
3.Wall Mounting
The pump is fastened horizontally by means of enclosed attachment
bracket with assembly material (± 2%) to a wall. Make sure, that the two
absorption rubber pieces are located under the plastic clamping latches
on the back side of the pump system. Pay attention to sufficient free
space upward and/or to a good accessibility for maintenance work. The
pump must be installed min. 30 cm over the tank level, so that no inlet
pressures can occur. The oil lifter can not be installed outside. The oil
lifter can be installed on a fire proof enclosure (30 mins) and have a fire
valve fitted.
4.Pipe Installation
The SP32-01 is factory equipped with sucking and outlet SERTO
cutting ring threaded connection for 8x1 mm CU pipes (ID 6 mm). When
connecting the CU pipes to the suction and outlet connecting piece it is
to be made certain, that no tensions at the connecting pieces result from
bending the lines, and downward gradient of at least 2% (with stove) is
present. The pipe installation must be implemented therefore expertly
and carefully. If the suction pump is installed more for than 3m over
a stove, an oil pressure-reducer must be inserted prior to the furnace
automatic controller. Note: when bending the lines no cross-section cont-
ractions may develop
• avoid over tightening the pump connections
• when assembling the pipes pay attention to tightness
• the legal guidelines for pipe installation are to be kept
Frequency Wattage
50 Hz 40 W
HYDRAULIC
Max. suction height
7 m 12 l/h
4 m 18 l/h
5.Electrical Installation
The electrical outlet must have an earth protective grounding – 230V
50Hz. The suction pump is delivered completely ready for installation
with a power supply plug according to VDE. The SP32-01 is protected
by a conducting path, located on the main PCB
Legend:
A.Main oil tank
B.Suction line pipe ID 6mm
C.Oil tank suction pump 1,6l
D.Safety catch pan
E.Cover
F. LED-display
G.Start-up button
H.Main electrical plug
J.Shut-off valves
K.Oil-pressure regulator
L.Appliance
M.Check valve
- 4 -
GB
MECHANICAL
Reseve- Gewicht netto
Storage
1,6 l 2 Kg
.